Complete the table in the picture FA =1NFB = 3 NTABULATIONTable 1.Reactions of a rigid bodyDynamometer Reading (N)Computed Reading (N)Load (N)Trial(Experimental Value)(Theoretical Value)No.FAFBRARBRARB2.71-2514 N|. 6 2.22.31N3 N1-5531N3 NCALCULATIONEF, = 0+ EM= 0Trial 1:Irsics (Sec 3)-20211130 140842-Meeting Reco842-Meeting Record Set upTrial 1900в150F. =4NTrial 2900100150F. =1NF. =3NTrial 3R.s00 mmB50250 mmmimFa =1NF=3N

solution on trail Aconsider ∑Fy=0RA+RB=4consider ∑Ma=0-RBx900+4x150 =0RB=0.67KN therefore RA=3.33KN

TABULATION Table 1.Reactions of a rigid body Dynamometer Reading (N) Computed Reading (N) Load (N) Trial (Experimental Value) (Theoretical Value) No. FA FB RA RB RA RB 2.7 |-25 1 4 N |. 6 2.2 1N 3 N 2.

TABULATION Table 1.Reactions of a rigid body Dynamometer Reading (N) Computed Reading (N) Load (N) Trial (Experimental Value) (Theoretical Value) No. FA FB RA RB RA RB 2.7 |-25 1 4 N |. 6 2.2 1N 3 N 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Convert 10 in to centimeter' 1 Add file

A: answer = 25.4 cm explanation is given in below step

Q: The six standard views in orthographic projection are front, top, bottom, and what?

A: Answer : Left view Right view Rear view

Q: Object 3. a. Replicate the front, left and top side views given using the 1st angle projection. Add…

Q: Use Scale ( 1:1), for the front and side views shown draw the isometric projection 50 30 25 40 80 30…

A: the isometric projection of the above front view and side view is

Q: Draw the isometric figure of the given multiview projection. HRP FRP ==== ====== FRP PRP 1 11

A: The multi view projections are given.Multiview Projection:A Multiview Projection is a technique of…

Q: 25 17.5 210 42.5 R23 R60 R50 R34 Scale 1:1

Q: What do you understand by the term color rendering index?

A: The color rendering of a light source alludes to its capacity to uncover the colors of different…

Q: Draw and Isometric view of a hexagonal pyramid of side 30 mm and height 50 mm

A: The isometric view is the three dimensional projection of the object in two dimension vies. And the…

Q: Generate isometric drawing from multiviews using drawing tools or free - hand. Use approximate…

Q: Show Isometric View.

A: Answer We can obtain the isometric view from given views in Autocad using the following steps 1)…

Q: 15.16 Refer to Figure 15.52. Using Michalowski's solution given in Figure 15.25 ('> 0). determine…

A: The kinematic approach of limit analysis is applied to the rigid rotational collapse mechanism by…

Q: 12. The ability to magnify details in a drawing or reduce the drawing to see it in its entirety is a…

A: Generally in AUTOCAD zooming can be directly done by using keyboard shortcuts like using the “+” key…

Q: Draw the multiview projection of the given isometric figure. L HRP FRP L L FRP PRP 1. Discuss how…

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A: Top View of the given object is as shown below.

Q: Draw the top, the front, and the right side orthographic views of the objects shown. Indicate when…

A: Top , front and side views of the given object can be drawn as

Q: What is orthographic view elaborate? Draw orthographic view of the given figure assuming any…

Q: Q.3. Use Scale (1:1), for the front and side views shown draw the isometric projection: 50 30 R30 30…

A: To get the isometric projection from the given views. 1. Draw two lines perpendicular to each other…

Q: Given the isometric view of the cut block objects shown, use rectangular grid paper to sketch a…

Q: Draw the front and top and side view for these?

A: For any object which is needed to be constructed or manufactured it is important to have drawings…

Q: Given the isometric view, provide the top, front, and right-side view

Q: According to Francis Ching, what is an interior elevation? An orthographic projection of a…

A: Francis D.K. Ching was a registered architect and a well known Professor Emeritus at the University…

Q: Create a hand drawing of the isometric view of this object to scale.

A: First Draw one missing view from the given two view by projecting lines. A. After getting the…

Q: Draw the multiview projection of the given isometric figure. L HRP FRP L 1. Discuss how did you draw…

Q: SKETCH AUXILIARY VIEW. SHOW ALL VISIBLE AND HIDDEN LINES.

A: An auxiliary view is simply known as the “helper” view because it shows the slanted part of the…

Q: Civil Engineering Using the drawing board, draw the following views in 3rd angle projection: a) An…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Draw the front, side, and horizontal projections

Q: Draw the figure below in AutoCAD, take a screenshot of your work and paste it to the spaced…

A: The following image shows the given figure drawn in autocad with dimensions along with name.

Q: 60 Looking at the x direction, provide the front view, top view, and left-side view using the meter…

A: WE HAVE TO DRAW THE LEET SIDE , FRONT VIEW AND TOP VIEW Looking at X direction, we conclude that…

Q: O mm 10 mm FIGURE 1

A: Always side view is drawn beside the front view because Height of the object will be equal . Front…

Q: Use Scale ( 1:1 ), for the front and side views shown draw the isometric projection 22 19 38 Ф 18 22…

A: Given Data :

Q: Define isometric view with an example

Q: 90 80 70 703 E.60 E50 40 E 40 30 E20 10 ) simple vertical staff gauge.

A: A staff gauge is used to measure water surface elevation or any another surface elevation.

Q: Q3: Draw the Full Sectional Front view and Top View of given object 70 50 10 45 430 70 15 10 88 40

A: The following figure shows the Full Sectional Front View of the object.

Q: draw an isometric view of HEXAGONAL PRISM where the base is 25mm and height 50mm.

A: Isometric view: It is also known as isometric projection. It is defined as the visual representation…

Q: Given the following isometric drawing, how many edges are drawn as points in the right side view of…

A: ASKED: To determine the number of edges of the given isometric drawing that are drawn as points in…

Q: Draw the right side elevation of the object with the given top and front elevations below ho.00…

Q: PART 1. AREA & VOLUME OF PRISMS Draw the indicated views for the isometric drawing below. Isometric…

A: An isometric view is given, we need to draw: 1. Top view 2. Left view 3. Front view

Question

Complete the table in the picture

FA =1N
FB = 3 N
TABULATION
Table 1.Reactions of a rigid body
Dynamometer Reading (N)
Computed Reading (N)
Load (N)
Trial
(Experimental Value)
(Theoretical Value)
No.
FA
FB
RA
RB
RA
RB
2.7
1-25
1
4 N
|. 6 2.2
2.3
1N
3 N
1-55
3
1N
3 N
CALCULATION
EF, = 0
+ EM= 0
Trial 1:
Irs
ics (Sec 3)-20211130 140842-Meeting Reco
842-Meeting Record

Set up
Trial 1
900
в
150
F. =4N
Trial 2
900
100
150
F. =1N
F. =3N
Trial 3
R.
s00 mm
B
50
250 mm
mim
Fa =1N
F=3N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Draw the minimum number of views necessary to represent the figure (for example top, front and / or right view)
Draw Thiessen Polygon
Please attach pdf/dwt or write out steps on how you got drawing please
Draw front view, side view and top view for the figure below
show the: top view and isometric/oblique drawing of the given figure
Given the isometric view, provide the top, front, and right-side view
1
Given the figure that shows front and top views of the object, how many of its visible and hidden faces are isometric planes in the isometric drawing? HRP FRP
What is the Moody Diagram used for? Edit View Insert Format Tools Table 12pt Paragraph B IU Αν VT² V
A Figure shows an isometric view of an object. Draw to a full size scale thefollowing views in first angle projection.(a) Sectional front view, (b) Top view and (c) Sectional side view
Explain two methods discussed in class for finding the area of irregular shapes.