Ta-1.2 kN-m 40 mm LEGGG 54 mm T-0.8 kNm 46 mm T-0.4 kN m 40 mill ASSIGNMENT 2.6 Under normal operating conditions, the electric motor exerts a torque of 2.4 kN m on shaft AB. Knowing that each shaft is solid, determine the maximum shearing stress in (a) shaft AB, (b) shaft BC, (c) shaft CD.

Ta-1.2 kN-m 40 mm LEGGG 54 mm T-0.8 kNm 46 mm T-0.4 kN m 40 mill ASSIGNMENT 2.6 Under normal operating conditions, the electric motor exerts a torque of 2.4 kN m on shaft AB. Knowing that each shaft is solid, determine the maximum shearing stress in (a) shaft AB, (b) shaft BC, (c) shaft CD.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: (a) A circular shaft used for transmission is 510mm in length and 50mm in external diameter. It is…

Q: Under normal operating conditions a motor exerts a torque of magni-tude TF= 1200 lb·in. at F.…

A: (a) Write the relation between the torques on shafts FGH and CDE and the radii of the gears G and D.…

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

Q: 3. A 220-mm-diameter steel shaft have a maximum shearing stress of 12 GPa. Determine the applied…

A: Write the formula for shear stress in the shaft under torsion. τ=16Tπd3 Here, τ is the shear stress…

Q: onsider a solid shaft of 1.4-in. diameter. Determine the maximum shearing stress in the shaft as it…

A: Given:diameter of shaft, d=1.4inPower of shaft, P=66hpSpeed, N=810rpm

Q: The stepped shaft shown rotates at 430 rpm. Knowing that r=0.5 in., determine the maximum power that…

A: Given: r=0.5 inN=430 rpmτmax=7500 psi

Q: C Тс 3 Tc 325 N - т 28 тт В Тв 3D 517 N — т 42 тm A

A: given data dia of shaft AB = 42 mm dia of shaft BC = 28 mm Torque TB = 517 N-m Torque Tc = 325 N-m

Q: Knowing that each of the shafts AB, BC, and CD consists of a solid circular rod. Knowing that both…

A: we are going to apply the Torsion equation over the shaft.

Q: The two solid shafts are connected by gears as shown and are made of a steel for which the allowable…

A: The given information in the problem is shown in the following attached image:

Q: A solid steel shaft will not twist through more than 3 degrees in a 6-m length when subjected to a…

A: Given data: The angle of twist, θ=3°. The length of shaft, L=6 m. The applied torque, T=12 kN·m.…

Q: A 5 hp motor transmits power to a pressure pump at 600 rpm. Determine the minimum required diameter,…

A: Given data: P = 5 HP = 2750 lbf-ft/s = 12*2750 lbf-in/s ∴ P = 33000 lbf-in/s N = 600 rpm τ = 12 ksi…

Q: Q.2) Three solid Brass (G = 44 GPa) shafts along with two sets of meshing gears are used to form…

Q: The steel jacket CD has been attached to the 40-mm diameter steel shaft AE by means of rigid flanges…

A: Given Data

Q: 3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B…

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A: Given: The allowable shearing stress in the shaft, τ = 55 MPa The length of shaft AB, LAB = 750 mm =…

Q: Q2/A solid circular transmission shaft of (2m) long with angle of twist not exceed (39) which used…

A: Given,Length of the shaft (L) = 2 mThe angle of twist (θ) = 3° = 0.052 radiansPower P = 2.5 hp =…

Q: A 2-m long hollow steel shaft (G = 75 GPa) has an outside diameter of 75 mm and an inside diameter…

Q: For the assembly of Fig. , knowing that rA= 2rB, determine the angle of rotation of end E of shaft…

A: Given that The relation between the radius is, rA = 2rB. Let TAD be the torque exerted on shaft AD.…

Q: The largest torque Tc that can be applied at Cis kip-in.

Q: 2. a. Knowing that the allowable shearing stress is 8ksi, for the stepped shaft shown, determine the…

A: Step 1: Step 2: Step 3: Step 4:

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A: if you have any doubts please comment

Q: Knowing that the lengths of the shown solid shafts are AB-60mm and BC=80mm, determine the torque TA…

A: Given. TB = 400 Nm θAC=3o G = 77 MPa LAB = 60 mm LBC = 80 mm

Q: 3) The electric motor exerts a torque of 600 N.m on the steel shaft ABCD when it is rotating at a…

A: Given Data Modulus of rigidity is : G=77 GPa Length section of BC is : LBC=0.8 m Length section of…

Q: Knowing that d = 1.2 in., determine the torque T that causes a maxi-mum shearing stress of 7.5 ksi…

Q: Q3: The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques as…

A: To find: The total angle of twist at end A. Given: The modulus of rigidity of the shaft is G=77 GPa.…

Q: Under normal operating conditions a motor exerts a torque of mag-nitude TF at F. The shafts are made…

A: Given, Torque at F = TF Allowable Shearing Stress in Steel Shaft ? = 12 kpi Diameter of FH dFH =…

Q: determine the bolt diameter required in mm. (b) If the shaft is made of the same material as the…

Q: Determie the rotation or twist in degrees of a shaft, 742 mm long subjected to a torque of 95 N-m,…

A: According to the given datawe need to findThe angle of the twist

Q: 100 mm mm E The two solid shafts ABC and DEF are connected via gears as shown. Both shafts are made…

Q: 1. (a) Determine the maximum shearing stress caused by a 80- kip x in. torque T in the…

A: Given Data Torque = 80 kip. in Diameter, D=3 in Length of the steel shaft, L=4ft

Q: 4. A line shaft with a power of 100 kW at a speed of 1,200 rpm, had a rectangular key in its pulley…

A: Power, P=100kWmax. shear stress for shaft τshaft=40N/mm2max. shear stress for key τkey=30N/mm2width…

Q: 3.36 The torques shown are exerted on pulleys B. C, and D. Knowing that the entire shaft is made of…

A: To find the angle of twist

Q: The design of a machine element calls for a 40-mm-outer diameter shaft to transmit 45 kW. (a) If the…

Q: ! Required information The torques shown are exerted on pulleys A and B. Consider TA = 360 N·m and…

Q: The shafts of the pulley assembly shown are to be redesigned. The allowable shearing stress in each…

Q: 7. What is the maximum torque in kN-m that can be applied to a hollow circular steel shaft of 120 mm…

Q: 3. A machine shaft is supported on bearings 1 m apart is to transmit 190 KW at 300 rpm while…

Q: A solid steel shaft will not twist through more than 3 degrees in a 6-m length when subjected to a…

Q: Consider a solid shaft of 18-mm diameter. Determine the maximum shearing stress in the shaft as it…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

100%

UNIVERSITY
of Prince Edward
ISLAND
i mm
GGGG
54 mm
T₁-1.2 kN-m
1-08 kNm
0
154
T-0.1 kN m
40 mm
ASSIGNMENT 2.6
Under normal operating conditions,
the electric motor exerts a torque of
2.4 kN m on shaft AB. Knowing that
each shaft is solid, determine the
maximum shearing stress in (a) shaft
AB, (b) shaft BC, (c) shaft CD.
ASSIGNMENT 2.7
Two shafts, each of -in. diameter, are
connected by the gears shown. Knowing that
G=11.2 x 10 psi and that the shaft at F is
fixed, determine the angle through which end

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

! Required information The torques shown are exerted on pulleys A, B, and C, where T₁ = 3 kip-in. and 72 = 7.4 kip-in. Assume that both shafts are solid and the diameter of shafts AB and BC to be 1.3 in. and 1.8 in., respectively. T1 10.4 kip.in. 48 in. B 72 in. T2 C Determine the maximum shearing stress in shaft AB. The maximum shearing stress in shaft AB is ksi.
OA A:YA دكوز شعبة B.png Knowing that the lengths of the shown solid shafts are AB=60mm and BC=80mm, determine the torque TA if the total angle of twist of disk A relative to the ground C is 3º. What are the corresponding shearing stresses for each shaft? Take G=77 MPa. TA 30 mm В TR = 400 N. m 46 mm II
A steel shaft 7 ft long that has a diameter of 5 inches is subjected to a torque of 47 kip ft. Determine the maximum shearing stress in ksi.
! Required information The torques shown are exerted on pulleys A and B. Consider TA = 360 N·m and TB = 400 N.m. TA 30 mm 46 mm B Knowing that both shafts are solid, determine the maximum shearing stress in shaft AB. The maximum shearing stress in shaft AB is MPa.
A plain flange coupling is used by a 75 mm shaft to transmit 50 kW at 100 rpm. It uses 6 bolts with a diameter of 20 mm. Determine the bolt circle diameter if the shearing stress of the bolt is 25 MPa. A. 102.32 mm B. 202.64 mm C. 152.16 mm D. 252.78 mm
Pravinbhai
a. Computation must be complete.b. Answer in two decimal places.c. Box your final answer.
Q.12A solid shaft of diameter 'd' and length " issubjected to torque T. Another shaft B ofsome length, material but twice the diameter is subjected to the torque 2T. The ratio of the angle of twist of shaft A to shaft B is-
A 0.75" diameter solid steel shaft is connected by the steel bolted coupling shown. The maximum allowable shear stress in the steel is 18 ksi (shaft and bolts). The coupling consists of steel bolts that are 1/8" diameter and the bolt holes are equally spaced and centered on a 4" diameter circle (2" radius from the center of the shaft to the center of a bolt hole). Determine a) The maximum torque that the shaft can carry Ans: /,491"* b) The number of bolts required for the torque in part a). Assume the bolts fail by shearing at the coupling interface and the shear stress is uniform across the bolt's cross sectional area.
The composite shaft shown consists of a 0.2-in.-thick brass jacket (Gbrass= 5.6 × 106 psi) bonded to a 1.2-in.-diameter steel core (Gsteel=11.2 × 106 psi). Knowing that the shaft is being subjected to the torques shown, determine the largest angle through which it can be twisted if the following allowable stresses are not to be exceeded: τsteel=15 ksi and τbrass= 8 ksi.
Required information A torque T= 51 kip-in. is applied at end A of the composite shaft shown. Know that the modulus of rigidity is 11.2 × 106 psi for steel and 4 x 106 psi for aluminum. 3 in. 2tin. A Steel - 100 in. Aluminum Determine the maximum shearing stress in the steel core. The maximum shearing stress is ksi.
Determine the maximum shearing stress (MPa) in a solid shaft of 60-mm diameter as it transmits 91 kW at a speed of 175 rpm.