o that it isan equalhe loadingch nail ofr of 0.25 in.so that it isan equaleter of thehe nails isbads.b/ftBandIf thehave a normalfail 350 MPa, determine the minimum diameter of eachwire. Use a factor of safety of 2.5.P7-62. The 50-kg flowerpot is suspended from wires ABand BC which have diameters of 1.5 mm and 2 mm,respectively. If the wires have a normal failure stress of 7fail = 350 MPa, determine the factor of safety of each wire.A30°BProbs, 7-61/6245°

Answered: Image /qna-images/answer/5dc7af23-cd26-4933-ab3b-87e342b8453c.jpg

t is ual ing of 5 in. it is ual the s is 7-62. The 50-kg flowerpot is suspended from wires AB and BC which have diameters of 1.5 mm and 2 mm, respectively. If the wires have a normal failure stress of 7 fail= 350 MPa, determine the factor of safety of each wire. O A 30° B Probs, 7-61/62 45° C

t is ual ing of 5 in. it is ual the s is 7-62. The 50-kg flowerpot is suspended from wires AB and BC which have diameters of 1.5 mm and 2 mm, respectively. If the wires have a normal failure stress of 7 fail= 350 MPa, determine the factor of safety of each wire. O A 30° B Probs, 7-61/62 45° C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Note: Express your answer in terms of the units. Observe 3 decimal places. The error threshold is ± 2.50% Relative to the right answer. 1.) The reaction @ point D 2.) The tension @ Cable BE. 3.) The x-component of the reaction @ A. 4.) The y-component of the reaction @A 5.) The reaction @ A.
HWAA traingular beam Beomm wide by 30omm height is Pinned at A, suPPorted by a cable CD and Carries a load (P) as shown in figure, Determine the max Valne of (P) that will not exceed a ombined normal stress of 120 Mla? Ans/ Prat - loo.3 W HoW:B Find the max Valne of (P) that canbe aPPlied on the Cantilever beam Shown in figure , knowing that the max Combined stresses will not exceed(22.67 MPa)in tension and (17.33 MPa) in cemPression? Ans/ Pmax 3D25W 450mm to Cable 30omm 150mm 50mm 300mm 2m Fig. (A) fig. (B)
Fig. P3.48 0.4 m 0.1 m B 0.3m 150 N-m 60 Nm Hibbeler F5-55. The assembly is made of A-36 steel and consists of a solid rod 20 mm in diameter fixed to the inside of a tube using a rigid disk at B. Determine the angle of twist at C. The tube has an outer diameter of 40 mm and wall thickness of 5 mm.
choose the correct answer
Maximum principal stress
Solve it ASAP
Н.W draw the deformation 18KN/m D 20 kN 40KN shape 12 kN/m 4 m B. 70KN 5m 5 m 10 kN 5 m Fig (3) Fig (4) 8 m 48 AN/m 100 kN El- constant Fint timt
Round off final ans only, dont round initial values ty
P9-1 B thanks
A) Bar AB is 60mm x 10 mm thick, E = 65 GPa, a1 = 9.5 x 10-6/°C. B) Bar BC is 20mm in diameter, E = 170 GPa, a2 = 7.5 x 10-6/°C.
Please solve this problem in double integration method
CE - PC 311 - STRUCTURAL THEORY Quiz No. 2F - Analysis of S tatically In determ in ate Beam s 1. By the moment-area method find the slope and de flection at the fre e end A of the cantile ver beam AB. E = 30,000k/in and I = 200 in ". Re fer to the fig ure belo w. A ll decim a ls must be in c lu ded, do not round off answers. All fig ures must be included and drawn straight. Curves may be done freehand. Sum marize your answers as shown b e lo w. w kit ft ft 1.110 7 8 Required Va lu es Answer O A A L1 L2 B.