T 30°- 50 mm 20 mm-| 10 mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. The vertical force acting on the rocker arm at A is FA = 50N, and at C it is Fc = 150N. When the smooth cam C is in the position shown, determine the magnitude of the force at B

T 30°- 50 mm 20 mm-| 10 mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. The vertical force acting on the rocker arm at A is FA = 50N, and at C it is Fc = 150N. When the smooth cam C is in the position shown, determine the magnitude of the force at B

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.38P: The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by...

See similar textbooks

Similar questions

The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
The woman is trying to move the crate of weight W by pulling on the rope at the angle to the horizontal. Find the smallest possible tension that would cause the crate to slide and the corresponding angle .
The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by the horizontal force P and a couple C (C is not shown on the figure). Find P and C.
Find the internal force system acting on section 3 for the pin-connected frame.
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a thrust hinge at A, a slider hinge at B, and the cable CD. Find the force in the cable and the magnitudes of the hinge reactions.
FA K mm L mm- M mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. When the smooth cam C is in the position shown, determine the force acting on pin B along Y axis and input its absolute value. (If your answer is negative, input its positive value such as -17 --> 17) Use the followings; FA=57N FC=246N K=51mm M=12mm L=22mm O=35degrees
2.0 m 100 kg 2.0 m 0.5 m 1.5 m 1.5 m The pulley at E is frictionless. Point B is a pinned connection; support A is a fixed support. The pin at C is in a smooth slot. s in: Determine the magnitude of of the x-component of the reaction force at A, Ax= N. Determine the magnitude of of the y-component of the reaction force at A, Ay= N. Determine the magnitude of of the external moment applied at A, MA= Nm. O O :
FA BO К mm L mm- M mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. When the smooth cam C is in the position shown, determine the force on the spring FD and input its absolute value. (If your answer is negative, input its positive value such as -17 --> 17 ) Use the followings; FA=57N FC=246N K=51mm M=12mm L=22mm O=35degrees ww
The jib crane is designed for a maximum capacity of 9 kN, and its uniform I-beam has a mass of 260 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.4 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 1.6 m? (b) What is the value of R when x = 3.2 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 32° x m 9 KN 1.0 m 2.6 m Questions: (a) If x= 1.6 m, R= i (b) If x= 3.2 m, R = i (c) The minimum value for R = i (d) The pin should be designed to hold i KN KN kN at x = i kN.
The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 230 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 2.0 m? (b) What is the value of R when x = 3.3 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 34° x 1.3 m 6 kN -2.9 m
The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (You can disregard the plot, I only need a, b, c, and d)