SW1 R1 R2 The circuit shows a capacitor, two ideal batteries, two resistors and a switch. Initally the switch has been open for a long time. If it is then closed for a long time, wha is the change in the charge on the capacitor? Assume that R₁ = 660, R₂ = 530, C=440 μF, V₁ = 9V and V2 = 21 V. == The change in the charge on the capacitor is equal to με

SW1 R1 R2 The circuit shows a capacitor, two ideal batteries, two resistors and a switch. Initally the switch has been open for a long time. If it is then closed for a long time, wha is the change in the charge on the capacitor? Assume that R₁ = 660, R₂ = 530, C=440 μF, V₁ = 9V and V2 = 21 V. == The change in the charge on the capacitor is equal to με

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
When the switch is in position 1, the circuit will charge the capacitor. Determine the equations for v(t) and i(t) for the charge phase and determine the voltage and current at time, t = 31 ms, in the charge phase.
lell L1 R Ro 2. In this figure, assume arbitrary numbers for R1, R2, L1, and L2 including some number for the battery E. Find the rate of current in which inductor one (L1) is changing just after the switch is closed. Next, find the current in L1 after some time after the switch has been closed. lell
Electrical Engineering I'm reading about the electronics in touch screen. It says when i touch the panel it distorts the electrostatic field and thus will have a change in capacitance. This is how it detects My question is the electrostatic field same as electric field? Please explain in details How did the capacitance change when i just touch the panel
How does the internal resistance of the multimeter (in voltage setting) affect the charging/discharging rate of the capacitor. Explain.
Determine the values of resistance R and inductance L
- Find the electric potential energy of the system of charges shown in the figure. NOTE: k=9x10 Nm²/C², uC=10-6C 2m 91=2µC 60° 92=2µC 2m 60 O 93-2μC
How temperature effect conductivity? Explain with the help of following equation. m e'n7'
For the network shown in figure (3), if the switch is closed for 2usec and then opened for Susec, find mathematical expressions for vi and in of both periods of time and then plot the waveforms of vL and i as a function of time.