Suppose you have a diode whose junction cross sectional area is 100µm? and has the following additional properties: А Jsx 0.5 A/um2 m VGO n 2.3 1.17V 1 100µm2 What is the current flow through the device if biased with a forward voltage of 0.6V at a temperature of 125°C? What about at 0°C? At 27°C? Are diodes temperature-dependent devices?

Suppose you have a diode whose junction cross sectional area is 100µm? and has the following additional properties: А Jsx 0.5 A/um2 m VGO n 2.3 1.17V 1 100µm2 What is the current flow through the device if biased with a forward voltage of 0.6V at a temperature of 125°C? What about at 0°C? At 27°C? Are diodes temperature-dependent devices?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

A silicon diode is in connected to a DC voltage source with Forward biased, the net currentflowing through the diode is (25mA) where the applied voltage across the terminals of thediode is (820mV). Determine diode temperature, if Is "dark saturation current", the diodeleakage current density in the absence of light is 3.4 × 10−10 A
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
Design a voltage-regulator circuit to provide a constant voltage of 5 V to a load from a variable supply voltage. The load current varies from 0 to 100 mA, and the source voltage varies from 8 to 10 V. You may assume that ideal Zener diodes are available. Resistors of any value may be specified. Draw the circuit diagram of your regulator, and specify the value of each component. Also, find the worst case (maximum) power dissipated in each component in your regulator. Try to use good judgment in your design.
Design a voltage-regulator circuit to provide a constant voltage of 5 V to a load from a variable supply voltage. The load current varies from 0 to 100 mA, and the source voltage varies from 8 to 10 V. You may assume that ideal Zener diodes are available. Resistors of any value may be specified. Draw the circuit diagram of your regulator, and specify the value of each component. Also, find the worst case (maximum) power dissipated in each component in your regulator. Try to use good judgment in your design. Repeat Problem P9.29 if the supply voltage ranges from 6 to 10 V.
Consider a silicon pn junction diode at T 300K. The reverse saturation current is Is = 10-14 A and the ideality factor n = 1. Determine the diode current for a diode voltage of VD = 0.573 V and use that to determine the DC and AC resistance of the diode. RDC = 14.13 k rac = 639 Q RDC = 234 Q2 = rac=8Q RDC = 7.00 KQ rac = 307 Q RDC = 1.43 kQ rac = 58 Q
Suppose we have a 10-V-peak sinusoidal voltage source. Draw the diagram of a circuit that clips off the part of the sinusoid above 5 V and below -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. Be sure to label the terminals across which the clipped output waveform vo(t) appears.
Analyze the ON/OFF states of all diodes (D1 and D2) inthis circuit, using the ideal-diode model.
Given the relationship for semiconductor diode is : I = Io ( exp(eV/kT)-1). Proof the equation in case of PN junction.
Consider a junction diode has dc biased current at operating point ID=0.8 mA. A sinusoidal voltage is superimposed on the VD such that the peak-to-peak sinusoidal current id(t) = 0.05ID. Find the value of the applied peak-to-peak sinusoidal voltage vd(t).
A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 kQ and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * A. 10 V B. 1.0 V C. 0.7 V D. 0.3 V
With constant current flowing in the forward direction in a small-signal silicon diode, the voltage across the diode decreases with temperature by about 2 mV/K. Such a diode has a voltage of 0.650 V, with a current of 1 mA at a temperature of 25°C. Find the diode voltage at 1 mA and a temperature of 175°C.
In the circuit shown in the figure, diode voltages are given as 0.6V and rD = 100 ohms. When point B is open circuit AIf + 5V is applied to the point of application, drawing the shape of the circuit formed and calculating the currents passing through the resistors.calculate.