1 Suppose that the temperature of heated plate at outer edges as shown in figure below.0²T 8²TUsing Laplacian Difference Equation ) + -=0( with Central Divided Differenceox² oy²Method to construct and solve the Elliptic Equations assuming step size of 3m in both xand y directions. Showing all equations and work9m100°C60°C60°C60°C40°C20°C20°C20°C

Answered: Image /qna-images/answer/fd797326-ff03-4e33-9fe2-a847569981f7.jpg

Suppose that the temperature of heated plate at outer edges as shown in figure below. Using Laplacian Difference Equation). 0²T 0(with Central Divided Difference dy 2 Method to construct and solve the Elliptic Equations assuming step size of 3m in both x and y directions. Showing all equations and work

Suppose that the temperature of heated plate at outer edges as shown in figure below. Using Laplacian Difference Equation). 0²T 0(with Central Divided Difference dy 2 Method to construct and solve the Elliptic Equations assuming step size of 3m in both x and y directions. Showing all equations and work

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

-7 PROVE THAT THE ANGLE 15 (30°) 30° BY LAWS OF CONGRUENCY 毫 30°
At a certain instant, the particle of mass m has the position and velocity shown in the figure, and it is acted upon by the force F. Determine its angular momentum about point O and the time rate of change of this angular momentum. Use m = 2.8 kg, a = 0.58 m, b = 0.98 m, c = 0.60 m, and F = 100 N and v = 3.5 m/s. m F
Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 8 5 إجابتك
What is the normal force applied to the block?
Please accept
D= 1.75 in d= 0.75 in r= .120 in
1 2 B
8 the ban
Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…
Ģ₁ G6 ਸਿੰਘ G G₁ Họ G G @TOO,
Find the Ixx value for the plate as shown below, where b1=d2=18 mm, d1=85 mm,b2=65mm. (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNITS GIVEN IN THE BRACKET) b1 b2 d2 d1 O The X value (unit in mm) =.
answer this; The numerical value of ? can be calculated as mm