Suppose that a SW ARQ system with 1-bit sequence numbering has a time-out value that is less than the time required to receive an ACK. Station A sends 5 frames to station B. No errors occur during transmission of all 5 frames. One ACK is lost when it is transmitted the first time (see the following table), and no error occurs in re- transmission of that ACK. No errors occur during transmission of the other 4 ACKS. Sketch the sequence of frame exchanges that transpire between stations A and B. Last digit of your student ID number 0, 1 2, 3 4, 5 6, 7 8, 9 Lost ACK 2 3 4

Suppose that a SW ARQ system with 1-bit sequence numbering has a time-out value that is less than the time required to receive an ACK. Station A sends 5 frames to station B. No errors occur during transmission of all 5 frames. One ACK is lost when it is transmitted the first time (see the following table), and no error occurs in re- transmission of that ACK. No errors occur during transmission of the other 4 ACKS. Sketch the sequence of frame exchanges that transpire between stations A and B. Last digit of your student ID number 0, 1 2, 3 4, 5 6, 7 8, 9 Lost ACK 2 3 4

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Suppose that a binary message – either 0 or 1 – must be transmitted by wire from location Ato location B. However, the data sent over the wire are subject to a channel noise disturbance,so to reduce the possibility of error, the value 2 is sent over the wire when the message is1, and the value −2 is sent when the message is 0. If X, X = {−2,2}, is the value sent atlocation A, the value received at location B, denoted as R, is given byR = X + N ,where N is the channel noise disturbance, which is independent of X. When the message isreceived at location B, the receiver decodes it according to the following rule:if R ≥.5, then conclude that message 1 was sentif R < .5, then conclude that message 0 was sentAssuming that the channel noise, N, is a unit normal random variable and that the message0 or 1 is sent with equal probability, what is the probability that we conclude that the wrongmessage was sent? This is the probability of error for this communication channel
Consider the following scenario: Frames of 12000 bits are sent over a 400kbps channel using a satellite whose propagation delay is 270ms. Acknowledgements are always piggybacked onto data frames. (That is, in the case of stop-and-wait, the next frame cannot be transmitted until the entire frame containing the acknowledgement is received.) Five-bit sequence numbers are used. What is the maximum achievable channel utilization for (a) Stop-and-wait. (b) Protocol 5 (i.e., Go Back N). (c) Protocol 6 (i.e., Selective Repeat)
Consider the following sequence of frames using l-Frame (1), P-Frame (P), and BD-Frame (B) ID 1 3 4 6 7 8. 9 Туре В В В В Determine the transmission (decoding) order of the frames. P.
A cyclic redundancy check (CRC) is an error-detecting code commonly used in digital networks and storage devices to detect accidental changes to raw data. Propose your own Roll as data bits (e.g roll 1 to 100) and show how the sender adds the parity bits and write the final code word that will be sent. Value of Key is 1011 (derived from polynomial function). Also show in the receiver side that the correct data is received.
Consider the following bit stream-a. 00000000 b. 11111111 c. 01010101 d. 00110011 Draw the graph of the i. NRZ-Iusing each of the given data streams, assuming that the last signal level has been positive. From thegraphs, guess the bandwidth for this scheme using the average number of changes in the signal level.
Asap
Write a program to simulate the behavior of the CSMA/CD protocol over Ethernet when ther are N stations ready to transmit while a frame is being transmitted. Your program should report the times when each station successfully starts sending its frame. Assume that a clock tick occurs every slot time (51.2 microsec) and a collison detection and sending of a jamming sequence takes one slot time. All frames are the maximum length allowed.
Consider a network with a data rate of 10 Mbps. Messages sent on this network have a maximum size of 1000 bits, including a 16-bit control field. What is the number of messages required to send a file F of 4 Mbits from one station to another? Assuming that a station cannot send a new message until it receives an acknowledgment of the successful reception of the previously sent message. The acknowledgment takes the form of a 16-bit message. A timer is set to a duration T after the sending of each message. If time T expires before receiving an acknowledgment, the sending station resends the same message. The distance between the two farthest stations in the network is 1 km. The signal propagation speed is v = 200,000 km/s. What is the minimum value of T? (You ignore the queuing time and the processing time and use only the propagation time and the transmission time)
Frames of 1000 bits are sent over a 106 bps duplex link between two hosts. The propagation time is 25 ms. Frames are to be transmitted into this link to maximally pack them in transit (within the link). 1.1 What is the minimum number of bits (1) that will be required to represent the sequence numbers distinctly? Assume that no time gap needs to be given between transmission of two frames.
Consider a network connecting two systems located 4000 kilometers apart. The bandwidth of the network is 500 x Mbps. The propagation speed of the media is 4 × 106 meters per second. It is needed to design a Go-Back-N sliding window protocol for this network. The average packet size is 107 bits. The network is to be used to its full capacity. Assume that processing delays at nodes are negligible. What is the minimum size in bits of the sequence number field?
Consider a half-duplex point-to-point link using a stop-and-wait scheme, in which a series of messages is sent, with each message segmented into a number of frames. Ignore errors and frame overhead. A. What is the effect on line utilization of increasing the message size so that fewer messages will be required? Other factors remain constant. B. What is the effect on line utilization of increasing the number of frames for a constant message size? C. What is the effect on line utilization of increasing frame size?
The maximum data rate that a medium of 10 KHz and S/N ratio of 30 dB is roughly: Select one: О . 10 Кbps O b. 30 Kbps О с. 2 Kbps O d. 100 Kbps