STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER A simply supported beam of span 6 meters is subjected a point load of 40.00 kN at a distance 4.00m from the left hand support. Calculate the position of maximum deflection of the beam from the left end support.  a. 2.58 m b. 2.85 m c. 0.85 m d. 0.58 m

Q: Calculate the deflection at the center of a simply supported beam in mm, if the beam has a length…

A: Given data- EI=4.5 m4 Pa

Q: . Determine the maximum deflection of the beam shown . Use conjugate beam method and take E =…

A: In conjugate beam method  HINGE support Changes to Roller and roller to hinge .  The conjugate beam…

Q: A 30mm diameter bar is 1.25 m long. When the bar is simply supported at its ends in a horizontal…

A:

Q: For questions 4A and 4B, the 3m simple beam is loaded as show Question 4A. Determine the location of…

A: To find maximum deflection

Q: Two simply supported beams are made up of the same material and are of the same cross-section. Both…

A:

Q: Using the "Effects Overlay" of the original beam, using isostatic sub-beams and simulating them…

A: Given that :- Modulus of Elasticity (E) = 200 GPa = 200,000 MPaWeight of the beam (W) = 2.5 Applied…

Q: For the beam in Question 2, suppose that instead of the pin support, we instead have a clam support…

A:

Q: [100 lb 80 lb A + 2 ft 4 ft 3 ft B.

A:

Q: Two simply supported beams are made up of the same material and are of the same cross-section. Both…

A: Given, load on both beam (udl) =w L1=2mL2= 4mEI= same δ1=1 mm

Q: For Beam KG (EI Constant), use the Unit Load Method to Determine: 1. The Deflection at F 2. The…

A: The given figure is shown below:

Q: The simply supported beam consists of a W460 × 82 structural steel wide-flange shape [E = 200 GPa;…

A: Given Data: E=200 Gpa I=370*10^6 mm4 P=62 kN w=28 kn/m LAB=LBC=2.9 m LCD=1.9 m   It is asked to…

Q: Part 2: By Super Position Consider the simple supported beam shown in the Fig. a. Determine the…

A:

Q: Determine the maximum deflection of the solid circular shaft illustrated in Figure 3. The shaft is…

A:

Q: beam with span of 12 m has overhanging portions at both ends and is loaded with a uniform…

A: Given Data:Overhanging beamSpan L=12mUDL= 28kN/mE=200 GpaI=1×109mm4 It is required to determine the…

Q: 2KN/ EI = 1600NM² 6m 4m Figure 06

A:

Q: A simply supported beam is loaded by a couple M at its right end. Find the M location of the maximum…

A:

Q: A simply-supported reinforced concrete beam, 300 mm wide x 600 mm deep spans 8 m. Its fundamental…

A:

Q: Using E=203,000MPa, calculate the actual maximum deflection of 90mm composite slab, with a steel…

A: To calculate the actual maximum deflection of the composite slab, we can use the formula for…

Q: Notes: Attempt Five Question only Q1: For the composite structure shown in Fig.(1), determine the…

A: Composite structures are commonly known as Load-bearing elements which consist of elements like…

Q: A 20 mm diameter bar is 1.25 m long. When the bar is simply supported at its ends in a horizontal…

A:

Q: A 20 mm diameter bar is 1.25 m long. When the bar is simply supported at its ends in a horizontal…

A:

Q: 1. Determine the maximum deflection of the simply supported beam. The beam is made of wood having a…

A:

Q: A cantilever beam, 4m long, carries a uniformly distributed load our total length. If the slope at…

A:

Q: The deflection at the free end of a uniformly loaded cantilever of length 1m is 7.5 mm. What is the…

A:

Q: 108 kN 21 6 m 4 m A,

A:

Q: For the beam and loading shown, determine the slope and deflection at the free end. The…

A: beam arrangement is given as shown in the figure above and it has been asked in the question to…

Q: QUESTION 1 Calculate the maximum instantaneous deflection in inch of the beam below. Ig = 67,831…

A: total load=6k/ft

Q: For the cantilever beam and loading shown, using the area moment method, determine the deflection at…

A: Given data  E =200 GPA = 200000MPA I =6.3617*10-7  M4  To calculate deflection at free end