SThe 4-mm-diameter cable BC is made of a steel with E = 200 GPa. Knowing that the maximum stress in the cable must not exceed 190 MPa and that the elongation of the cable must not exceed 6 mm, find the maximum load P that can be applied as

Q: The 54-kg homogeneous smooth sphere rests on the 28° incline A and bears against the smooth vertical…

A:

Q: The ratio of volume at the end of expansion to the volume at beginning of expansion is 12. Determine…

A: Given Data: The ratio of volume at the end of expansion to the volume at start of expansion is 12

Q: The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a construction…

A: Given Data The thickness of the plastic panel is:t=3mm=0.003 m The weight of the plastic panel…

Q: Find the determinant of the matrix by reducing the matrix to a triangular form. 1 3 14 9 1 15 D = -2…

A: given; D=1314391152-211-3423

Q: View Policies Current Attempt in Progress Two solid cylindrical rods (1) and (2) are joined together…

A:

Q: An insulated 8-m' rigid tank contains air at 800 kPa and 67°C. A valve connected to the tank is now…

A:

Q: Q3. Determine the dimensions of an I-section connecting rod for a petrol engine from the following…

A:

Q: Fill in the blanks: An Otto cycle has clearance volume of twelve percent. It produces three hundred…

A:

Q: create the front view of the sketch of the spur wheel

A: Given design:

Q: Determine the efficiency of a constant volume cycle with expansion ratio equal to 7.8. **Express…

A: Given Data The expansion ratio is:e=7.8 To find: The efficiency of the constant volume cycle. Now…

Q: Consider the truss shown in the figure below. Calculate the force on the member BC.

A: Answer: The force in the member BC is 60 lbs (compression).

Q: Given a gear of 24-tooth, 4- pitch, the clearance is to be one-eight of the addendum, and the…

A:

Q: 1200 N- m. 3.11 The solid steel shaft carries the torques T1 = 750 N - m and T2 Using L = L2 2.5 m…

A:

Q: A steel shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 50 MPa or…

A: Find the diameter of shaft.

Q: Third problem: Overhanging beam loaded with concentrated loads and couple moment.

A:

Q: . Determine the dimensions of an l-section connecting rod for a petrol ine from the following data:…

A:

Q: Determine the efficiency of a constant volume cycle with expansion ratio equal to 7.8.

A:

Q: A steel cable is used to lift a load W with the following given. weight W = 175 kN diameter = 30.03…

A:

Q: Date for benzene (1) + cyclopentane (2) at 35 0C were obtained by Horsemen & Prausniz (1963).…

A: Housemen & Prausniz achieved date jou benzene (1) + cyclopentane (2) at 35°C (1963). With the…

Q: The uniform beam has a mass of 55 kg per meter of length. Determine the reactions at the supports.…

A:

Q: An extension spring made from A313 stainless steel has a mean coil diameter of 10.00 mm and spring…

A:

Q: Consider a system where a horizontal, laminar, separated flow of air and water at 100 kPa pressure…

A: Area at inlet- H1=m˙v1V1H1=14×0.077190H1=0.012088m2

Q: wo degrees of freedom mass spring system below. Assume M = 1 = 100 N/m, K2 = 150 N/m, K3 = 867 N/m…

A:

Q: 7 A steel pinion has 16 teeth of module 6 and rotat 600 r/min, driving a gear of cast-iron with a…

A:

Q: When the bar rotates around point O, the position of the collar sliding along the bar is given by r…

A: This problem is related to velocity and acceleration analysis. if the bar is rotated with angular…

Q: An aircraft is flying at an altitude of 10000ft and at a certain part of its airframe a dynamic…

A: Write the expression of velocity at an altitude of 10000 ft. v22=gz-Pρ

Q: The acceleration of a particle is defined by the relation a = -kVv, where k is a constant. Knowing…

A:

Q: Consider a compression-ignition engine with compression ratio of 16.5 and temperature at the…

A: Given that: Compression ratio of the compression ignition cycle is 16.5. Temperature at the…

Q: Consider an air-standard Otto cycle that has a compression ratio of 7.8 and a heat addition of 1250…

A:

Q: Determine the capacity, in liters, of the punch bowl shown if R= 370 mm. (Round the final answer to…

A:

Q: Cable AB exerts a force of magnitude F = 4.6 N on point A. Express Fas a vector in terms of the unit…

A:

Q: Consider the truss shown in the figure below. Calculate the force on the member BC. A 5 ft D

A: Given: The structure,

Q: 3- Two cars muvng towards each other, separated by 150 km, If the first car has a speed of 60 m/s…

A:

Q: A mass spring system has a mass of 3/4 kg, a damping constant of 3/2 kg/sec and a spring constant of…

A:

Q: After isentropic expansion, the temperature is 1900 K.Consider a compression-ignition engine with a…

A:

Q: Consider the two point BVP: -u" + 3u = 1, 0<x<1, with u(0) = u(1) = 0

A: A two-point boundary value issue is defined when the solution and derivatives are stated at only…

Q: The pressure drop across a ball valve in a uniform diameter pipe is P1-P2 = 3572 psf. The inside…

A:

Q: steel pinion has 16 teeth of module 6 and rotates 600 r/min, driving a gear of cast-iron with a gear…

A:

Q: HomeWork: Draw the shape below using the Front View for drawing in 2D and then the Southwest…

A:

Q: An aircraft is flying at an altitude of 100ooft and at a certain part of its airframe a dynamic…

A:

Q: The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T is…

A:

Q: 0.5 kg of ammonia is contained in a piston-cylinder assembly, initially at T1= - 20•C and a quality…

A: Given data as per the question Mass of ammonia =0.5 kg Initial temperature =-200 c Quality =25%…

Q: Determine the efficiency of a constant volume cycle with expansion ratio equal to 7.8. **Express…

A: Constant volume cycle is nothing but OTTO air standard cycle. Given expansion ratio = re = rc = 7.8…

Q: For an installed capacity of 35 kW and a design flow of 150 l/s, what is the head required if the…

A: Power, P= 35 kW= 35000 W Discharge, Q= 150 l/s= 0.150 m3/s Overall efficiency, η= 70%= 0.7   To…

Q: 12-29. A particle is moving along a straight line such that when it is at the origin it has a…

A:

Q: 2. Humid air at 35o C and a pressure of 1 atm and with 98% relative humidity enters a condenser in…

A: Given: Properties of humid air  T1=35oCP=1 atmRelative Humidity φ=98%Tcond=15oC=288…

Q: Using the techniques outlined in Appendix A, Example A.5 or A.6, the Z section has principal moments…

A:

Q: Determine the efficiency of a constant volume cycle with expansion ratio equal to 7.8. **Express…

A:

Q: 1. For the system shown, the spring constantk = 400 kN/m, damping coefficient zeta = 0.5 and the…

A:

Q: The volumes of states 1, 2 and 3 of a diesel cycle operating on an air standard are 300 cm3, 2 x…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.