Steel Stress-Strain diagram. Which of the following statements is NOT correct? Engineering stress is the stress computed using the original area and not the necking down area. The constant stress region is called the yield plateau or plastic range. The linear portion is also called the plastic range. The proportional limit, elastic limit, upper and lower yield points are very close to one another and are treated as a single point called the yield point.

Steel Stress-Strain diagram. Which of the following statements is NOT correct? Engineering stress is the stress computed using the original area and not the necking down area. The constant stress region is called the yield plateau or plastic range. The linear portion is also called the plastic range. The proportional limit, elastic limit, upper and lower yield points are very close to one another and are treated as a single point called the yield point.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The components of plane stress at a critical point on a steel shell are shown in the figure below. The yield stress (Gy) of the material in simple tension is 250 MPa. 60 MPa 40 MPa 70 MPa (a) Determine the magnitude of the principal stresses and maximum shear stress. Sketch these on appropriately orientated elements. (b) Calculate the factor of safety against yield on the basis of i. Tresca failure criterion ii. Von Mises failure criterion
At a point in a component, the state of stress is shown on the element below. Assume that the stress magnitudes are s,-7150 psi and Sy - 4475 psi. The stresses act in the directions indicated in the figuure. Determine the magnitude of the absolute maximum shear stress that acts at the point. Answer: Tmax psi
At a point on the surface of a machine component the stresses acting on the e face of a stress element are or = 55 MPa and Txy = 30 MPa (see figure). T- 30 MPa a, = 55 MPa What is the allowable range of values for the stress oy if the maximum shear stress is limited to TO = 34 MPa? Round to one decimal place. (a) Lower limit is MPa (b) Upper limit is MPa
Direct stresses of 120 N/mm2 (tension) and 90 N/mm2 (compression) are applied at a particular point in an elastic material on two mutually perpendicular planes. The principal stress in the material is limited to 200 N/mm2 (tension). Calculate the allowable value of shear stress at the point on the given planes. Determine also the value of the other principal stress and the maximum value of shear stress at the point using Mohr’s Circle.
Strength For the state of plane stress shown, determine the largest value of o, for which the maximum in plane shear stress is equal to or less than 75 MPa. After you determine the value, draw Mohr circle for the case
4- The stress tensor at a point under the working load condition is given. The yield stress of the material in uniaxial tension test is Fy (MPa). Based on the von Mises criterion, calculate the factor of safety of the stress state against failure if all stresses are increased proportionally to reach the yield surface. Fy (MPa) 25 50 0 σ= 50 100 0 MPa 0 0 280 -50
2D stress at a point is given by a matrix 100 301 = [1 30 20 shear stress in MPa is Oxx Txy Tyx Oyy The maximum MPa
The state of stress at a point in a machine component is given by o, = 120 MPa, o, = 55 MPa, G = -85 MPa, Gy = -55 MPa, ox = -75 MPa, and o, = 33 MPa. Construct the Mohr's circles of stress for this stress state and find the maximum shear stress.
1- Determine the orientation measured clockwise to the principal plane (in degrees). 2- Transform the state of stress shown by rotating its orientation 50 degrees counterclockwise. What is the normal stress (in MPa) on the face which originally had the 75 MPa compressive stress (i.e. the top and bottom of the element). Make sure to enter a positive answer if it is in tension and a negative answer if it is in compression.
Find the value of normal stress if force applied is 2 N and cross sectional area 2 mm2
An originally rectangular rubber piece is deformed into the shape given by thedashed lines. Calculate,(a) The average normal strains along AC and BC.(b) The shear strain xy at all corners
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.