Steel design.The lap joint shown consist of bolts 22mm in diameter in 25mm diameter holes, The plates are A36 steel with Fy=250MPa, and Fu=400MPa. Use x1=50 mm ,x2= 160mm ,x3=60mm and plate thickness t=12mm for this problem.The allowable stress are:Bearing stress on project are,Fc=1.5FuTension on the net area of plates,Ft=0.5FuShear on the plates, Fv=0.3FuShear strength of bolt,Fv=210MPaDet. the value of Load P based on bolt shearDet. the value of Load P base on bearing on projected area on plate.Det. the value of load P based on block shear Problem 2The lap joint shown consists of bolts 22 mm indiameter in 25 mm-diameter holes, The plates areA36 steel with Fy = 250 MPa and Fu = 400 MPa. UseX1= 50 mm, x2 = 160 mm, x3 = 60 mm and platethickness t 12 mm for this problem.The allowable stresses are:Bearing stress on projected area, Fp = 1.5 FuTension on net area of plates, F= 0.5 FuShear on plates, F, = 0.3 FuShear strength of bolt, Fv 210 MPa- Determine the value of load Pbased on bolt shear.- Determine the value of load Pbased on bearing on projected area on plate.- Determine the value of load P based on block shear.10-0--

We have to determine the value of load P based on bolt shear and value of P based on bearing on…

Steel design. The lap joint shown consist of bolts 22mm in diameter in 25mm diameter holes, The plates are A36 steel with Fy=250MPa, and Fu=400MPa. Use x1=50 mm ,x2= 160mm ,x3=60mm and plate thickness t=12mm for this problem. The allowable stress are: Bearing stress on project are,Fc=1.5Fu Tension on the net area of plates,Ft=0.5Fu Shear on the plates, Fv=0.3Fu Shear strength of bolt,Fv=210MPa Det. the value of Load P based on bolt shear Det. the value of Load P base on bearing on projected area on plate. Det. the value of load P based on block shear

Steel design. The lap joint shown consist of bolts 22mm in diameter in 25mm diameter holes, The plates are A36 steel with Fy=250MPa, and Fu=400MPa. Use x1=50 mm ,x2= 160mm ,x3=60mm and plate thickness t=12mm for this problem. The allowable stress are: Bearing stress on project are,Fc=1.5Fu Tension on the net area of plates,Ft=0.5Fu Shear on the plates, Fv=0.3Fu Shear strength of bolt,Fv=210MPa Det. the value of Load P based on bolt shear Det. the value of Load P base on bearing on projected area on plate. Det. the value of load P based on block shear

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.12.2P

See similar textbooks

Similar questions

PROBLEM 7. Determine the largest load P that can be applied the plate and bolts. The bolt has a diameter of 12 mm and an allowable shear stress of 80 MPa. Each plate has an allowable tensile stress of 60 MPa, an allowable bearing stress of 70 MPa, and an allowable shear stress of 30 MPa. Answer: P = 25 kips (controls) P/2 P/2 30 mm- 15 mm P 30 mm
Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The bolts are 3/4 in. diameter. The steel is A572 Gr. 50. Check yielding and fracture. Check Block Shear. T 3in. 73im 13in 1 3in t
Situation 2. Two plates each with thicknessF16mm are bolted together with6 -22mm dimater bolts forming a lap conne ction. Bolt spacing are as follows: S1 = 40mm, S2 = 80mm, Sa = 100mm. Bolt hole diameter=25 mm 50 250mm 30 30 60 75 Allowable stress: Tensile stess on gross area of the plate=0.60 Fy Tensile stress on net area of the plate=0.5Fy Shear Stress of the bolt Fv=120MPA Bearing Stress of the bot Fp=1.2 Fu Calculate the permiss ible tensile load P under the following Conditions: 4. Based on shear capacity of bolts 5. Based on bearing capacity of bolts 6. Based on block shear strength (taking into consideration the failure path given in the figure below) 40 80 16 mm 40 180 mm 40 Bearing Failure Path #1 140 209 Bearing Failure Path #2
A double-row butt joint is used as a connection. It is made up of two 210mm by 12mm cover plates and 210 mm by 20 mm main plate. The plates are to be connected by 22 mm diameter rivets. The allowable stresses are 65 MPa for shear, 83 MPa for tension, and 135 MPa for bearing. Assume that each hole is 3 mm larger than the rivet diameter. Calculate the largest value for P that can be applied without exceeding the allowable stress for tension. o a. 418.3 kN b. 330.8 kN c. 348.6 kN (Ctrl) o d. 265.6 kN Pe
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
The bolts in the lap joint shown are 22mm in diameter and 25mm diameter holes. The plates are A36 steel with Fy = 250MPa and Fu = 400Mpa. For this problem, x1 = 500mm, x2 = 160mm, x3 = 60mm and t = 12mm. The allowable stresses are: Bearing Stress on projected area of the plates Fp = 1.5Fu Tension on net area of plates, Ft = 0.5Fu Shear on plates, Fy= 0.3Fu Shear strength of bolt, Fv= 210 Mpa a.) Determine the value of P based on bolt shear b.) Determine the value of load P based on bearing on projected area on plate (area in contact with the plate and bolts) c.) Determine the value of P based on block shear (use net area for block shear and use the diameter of hole)
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the design tensile strength of the section based on yielding of the gross area. Answer: |0 O O О о
ZAO O "l zain IQ YA docs.google.com/forms 10/.. find the shear stress in bolts 2 3 1. 5 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 110 MPa. 127 MPa. 509 MPa no one 0/10 find the tensile stress in upper plate in section 1-1 (2 (5 (3 1 4) + ...
Six rivets are used in the connection shown in the figure. If both P=50KN, what is the minimum diameter rivet is necessary so as not exceed the 70MPa allow shearing stress? What thickness of plate is required so as not exceed a bearing stress of 140MPA? p= 50 80 mm 80 mm 100 mm
ll zain IQ 37 MPa no one 10/10 find the tensile stress in upper plate in section 3-3 5 1 4 80 kN 80 kN B-bolt DIA. 10 MM 80 kN 80 kN B-bolt DIA. 10 MM 10 MPa 12.5 MPa 15 MPa 8.5 MPa no one 10/ find the bearing stress between bolts and plate
Two plates each with thickness t= 16 mm are bolted together with 6-22mm bolts forming a lap connection. Bolt spacing are as follows: S1=40 mm, S2=80 mm, S3=100 mm. Bolt hole diameter= 25mm. (a)Compute the bearing stress of the bolt and hole if the P = 200KN. (b)If allowable bearing stress is 480MPa, compute the value of P.