Steam with 136 kg/s at 5.0 Mpa, 420oC expands in a Rankine turbine to 0.036546 Mpa. a) For Rankine cycle, determine the heat added, heat rejected, turbine work, pump work and cycle efficiency. b) For Rankine engine, determine the heat added, net work, and engine efficiency. (Note: Draw the schematic and T-s diagram)

Q: alculate the NPSHA of the figure below essel Pressure = 134.6 psia Minimum Operable Liquid Level 15 ...

A:

Q: Problem 2 GIVEN: The rectangular bar, h = 3-mm thickness, shown is loaded axially with constant forc...

A:

Q: Water stored in reservoir to a depth of 2 m above the entrance of pipe a 20 cm diameter pipe dischar...

A:

Q: Example/ A slab of steel in circular section with diameter 0.02m ane length 0.4m exposed into a tens...

A:

Q: Water flows to a pump at 100 psig and the pump supplies 100 feet of head pressure. If piping losses ...

A: Pressure inlet to pump, P1=100 psig=100*144 lb/ft2Pump head, Hp=100 ft

Q: 2.51 The force F - 18i – 12j + 10k Nis applied to the gripper of the holding device shown. Determine...

A: Given   Force, F=18i-12j+10k N Find   Moment about a-axis    Moment about z-axis

Q: Write the finite difference form of the two dimensional steady state heat conduction equation with i...

A: Given value-∆x=∆y=0.01k=25w/mkq=107 w/m3

Q: 1.31 Resolve the 360-b force into components along the cables AB and AC. Use a- 6P and A – 40°. 360 ...

A: Given data as per question Force applied at point A =360 lb α =600β=400

Q: A volume of 0.01 L of water at 60°C is maintained in a cylinder 110 mm in diameter. A 95.86 kg pisto...

A:

Q: A distance was measured with an electronic infrared device, during which the influential weather ele...

A: the correlation is calculated from the following relation:   where,∆t= 32-26 = 6°C∆p = 670-680 = -10...

Q: 2.17 The trapdoor is held in the horizontal plane by two wires. Replace the forces in the wires with...

A: F1=240NF2=300NDB=1.2mBE=1.2mTo-Find:-The y-coordinate of point A

Q: Two identical springs of spring constant 7580 N/m are attached to a block of 0.245 kg as shown in th...

A: GIVEN DATA- A SPRING MASS SYSTEM GIVEN MASS m=0.245kg K=7850N/m WE HAVE TO FIND NATURAL FREQUENCY

Q: Position tolerances applied to features that result in a fixed fastener condition usually require a(...

A: Position tolerance applied to feature that result in a fixed fastener condition usually require 1) p...

Q: 3. A diver of weight W is springing on a rectangular cross-sectional diving board ABC. On a particul...

A: Given: weight of the diver→W=600 N height of the diver→h=500 mm = 0.5 m youngs modulus→E=12.6 GPa=12...

Q: A steel tube with a circular cross section has an outside diameter of 294 mm and wall thickness of 2...

A:

Q: 2. A gas turbine that operates on Brayton cycle provides a furnace with hot pressurize through its e...

A:

Q: 4. Specific Weight is also called Relative Density. 5. Standard density of water in English unit is ...

A: It is required to determine whether the following statements are correct or not: 4. Specific weight ...

Q: Linear spring P Consider a cylinder-piston system with cross sectional area 0.2 m² that has compress...

A:

Q: The beam shown below is under a concentrated load P at the free end (point C). The bending rigidity ...

A:

Q: The shaft is supported by smooth journal bearings at A and B that only exert vertical reactions on t...

A:

Q: 1. The four sides of a square plate of side 12 cm, made of homogeneous material, are kept at constan...

A:

Q: G. In the Study of rheological poperbes ot a Choco la te product, the Viscosity CH.) of the product ...

A: The relationship between shear stress and time has been provided. It is asked to find the linear rel...

Q: Compute the elevation considering the atmosphere as a static fluid which has a final value of 8.43ps...

A: Atmospheric pressure: Air pressure, otherwise called barometric tension (after the indicator), is th...

Q: 1. A circular piece of wood, 90mm in diameter, is used as a compression block. Determine the axial f...

A:

Q: A jet of water of diameter 75 mm moving with velocity of 25 m/s strikes a fixed plate in such a way ...

A: Given Data: Velocity, v=25 m/s Diameter of jet, d=75 mm

Q: Oil (SAE 30) at 15.6 °C flows steadily between fixed, horizontal, parallel plates. The pressure drop...

A: Given data Oil ( SAE 30) at 15.6oC flows between fixed horizontal parallel plates Pressure drop per ...

Q: 3. If a miniature engine does 520. J of work to cause a car in motion with a distance of 260, m, how...

A:

Q: Draw the free-body diagram for the boom. Connection at A is a pin. Draw the vectors starting at the ...

A:

Q: Discuss different design of aspects of PEV, BEV and HEV with suitable diagrams?

A: Hybrid electric vehicle: HEVs are the most common type of hybrid, and they have been around the long...

Q: 7) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 40 mm. The...

A: Given Data: Diameter of cylinder, d=550 mm Thickness, t=40 mm

Q: Q9c. For the beam below, the point loads and distances are as follows: F1 11.25 kN, F2 11.25 kN and ...

A:

Q: long does it take a plane, tr

A: Need to find Time 

Q: Draw the free-body diagram for the boom. Connection at A is a pin. Draw the vectors starting at the ...

A: Free Body Diagram (FBD) is the graphical representation of forces acting on body. The forces are rea...

Q: Design a piston for use in automobile engines (piston ring, pin, skirt).

A: Design analysis and optimization of piston:- 1.which is stronger,  lighter with minimum cost and wit...

Q: Define the critical temperature as Tc and critical pressure as the refrigerants R-134a and R-410a. P...

A: We can define critical temperature as temperature over which a gas will not be able to liquify on th...

Q: Draw a sound conclusion based on how you familiarized the key components of the lathe machine. Empha...

A:

Q: Show the temperature distribution in degree Celsius in an exhaust valve of IC Engines.

A: Internal combustion engines usually consists of two types of engine valves Inlet valves and exhausts...

Q: A piston-cylinder device with a set of stops initially contains 0.3 kg of steam at 1.0 MPa and 400°C...

A: Given data :  Mass m = 0.3 kg  Pressure P1 = 1.0 MPa  Temperature T1 = 400 °C Pressure P2 = 1.0 MPa ...

Q: When subjected to a compressive load, the length of the rod is 199,6 mm, and its diameter is 10 mm. ...

A: GIVEN DATA-  Final length of the rod is 199.6 m Intial Length 200mm Diameter d=10mm E=70GPa  

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown, determi...

A:

Q: If the beam is subjected to a bending moment M = 50 kN-m, determine a.) the maximum bending stress ...

A:

Q: Two parallel shafts, 92 cm apart, are connected by a belt drive. The driving pulley rotates at 300 r...

A:

Q: Open with STAY 3 SECONDS BEHIND in good driving conditions at 50 km/h 50 one-thousand-one, one-thous...

A: Consider a car travelling under the given conditions Velocity = 50 km/h = 50 x 518 m/s = 13.889 m/sT...

Q: What is the main cause of the increase in drag when you increased the angle of attack?

A: Drag is the aerodynamic effect that affects the motion through air. It is generated due to relative ...

Q: Water stored in reservoir to a depth of 2 m above the entrance of pipe a 20 cm diameter pipe dischar...

A: We have given data from the question: h=2 m, d=20 cm=0.1 m L=80 m Slope=1 in 100,  f=0.017

Q: The velocities of the particles at an instant are VA = 5m/s and VB = 7m/s, with the angle between th...

A: Given data vA = 5 m/svB = 7 m/sAngle between vA and vB = θ = 37.5°

Q: Make a research topic and 3research questions about SOLAR PANELS IN THE MIDDLE OF THE HIWAY HAVE A B...

A:

Q: for the cirele below (Reg) sedroh fon 300 150 se RI R43502

A:

Q: 3. Link AB is rotating at a rate of 6 rad/s constantly CCW. Determine the angular velocity of links ...

A:

Q: The inlet and throat diameters of a horizontal venturimeter are 30 cm and 15 cm respectively. The li...

A: Given that, Diameter of inlet d1=30 cm=0.30 m Diameter of throat d2=15 cm=0.15 m Specific gravity S=...