Steam is supplied to a fully loaded 100-hp turbine at 200 psia with u; = 1163.3 Btu/lb, v; = 2.65 ft³/lb and u1 = 400 ft/s. Exhaust is at 1 psia with uz = 925 BTU/lb, v2 = 294 ft2/lb and uz = 1100 ft/s. The heat loss from the steam in the turbine is 10 Btu/lb. Neglect potential energy change. Determine: a. the work per Ib steam b. the steam flow rate in Ib/hr u, = 1163.3 Btu/lb u, = 925 BTU/lb V, = 2.65 ft /lb v, = 294 ft /lb P,= 200 psia Turbine P2= 1 psia

Steam is supplied to a fully loaded 100-hp turbine at 200 psia with u; = 1163.3 Btu/lb, v; = 2.65 ft³/lb and u1 = 400 ft/s. Exhaust is at 1 psia with uz = 925 BTU/lb, v2 = 294 ft2/lb and uz = 1100 ft/s. The heat loss from the steam in the turbine is 10 Btu/lb. Neglect potential energy change. Determine: a. the work per Ib steam b. the steam flow rate in Ib/hr u, = 1163.3 Btu/lb u, = 925 BTU/lb V, = 2.65 ft /lb v, = 294 ft /lb P,= 200 psia Turbine P2= 1 psia

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

10. A container with a movable piston holds 2.00 moles of a monatomic ideal gas at a pressure of 3.0 × 105 N/m2 in a volume of 0.018 m3 . (a) What is the temperature of the gas? (b) The gas undergoes an isothermal expansion to a volume of 0.027 m3 . How much work does the gas do during this expansion? (c) How much heat flows into or out of the gas during this expansion? Does it flow into or out of the gas?
4. Water at 100 psig is flowing inside a 2 in sch 40 pipe (D₁ = 0.1723 ft) at a rate of 25 lb/s, then it flows through an additional pipe of 1 in sch 40 (D2 = 0.0874 ft) and leaves this second pipe at 40 psig at an elevation 20 feet above the inlet to the large pipe. No pump is used in the set- up. The net heat imparted from the surrounding is 1500 BTU/hr. Calculate the total friction expressed in lbf-ft/lb.
A solid cylindrical bar conducts heat at a rate of 25 W from a hot to a cold reservoir under steady state conditions. If both the length and the diameter of this bar are doubled, the rate at which it will conduct heat between these reservoirs will be O 12.5 W. O 200 W. O 100 W. O 25 W. O 50 W.
A 1500-W hotplate is used to heat up a 1.04kg aluminum pot filled with 1.22kg of water and a 0.855kg lead mass for 5 minutes. If the initial temperature of the system was 72 degrees F, find the final equilibrium temperature. Assume that all the energy of the hot plate goes into the system. (C water = 4180 J/kg*K , C aluminum - 910 J/kg*K, C lead = 160 J/kg*K).
A steam boiler has a total volume of 4 m3. The boiler initially contains 3 m3 of liquid water and 1 m3 of equilibrium steam at 0.1 MPa. The boiler is turned on and heat is transmitted to the water and steam. Meanwhile, the inlet and outlet valves of the boiler remain closed. The safety valve escapes when the pressure reaches 5 MPa. How much heat is transmitted to the water and steam before I open the safety valve?
2. In an experimental set-up, 5 kg of salt solution is heated in a glass vessel by a 159 W power gas burner. The internal energy of the solution is to be increased from 90 kJ/kg to 178 kJ/kg for a certain amount of time. An electric stirrer is used to ensure uniform heating of solutions, the power consumption of the stirrer is 30w. The rate of heat loss from the vessel 50o W. How many minutes was the solution heated if the motor is 80% efficient?
64870 J of heat is added to a gas at a constant pressure of 1.75 x 105 Pa This causes a change in internal energy of 2570 J. If the starting volume is .864 m3, what is the final volume?
A 6-cylinder, two-stroke, diesel engine produces 1092 hp at 360 rpm. The engine has an expansion ratio of 5, a percent clearance of 3.0%, and a mechanical efficiency of 77.3% when it is operating at 31.3 0C and 101.7 kPa standard atmospheric conditions. It is then used as a generating unit by a plant at an elevation of 3289 ft where it gave a brake heat rate of 18,530 kJ/kW-hr at k=1.37 using a fuel having a heating value of 42,000 kJ/kg. Find BPo in HP Correct Answer: 987.25
In a fruit juice facility, pear juice is heated from 20 C (feeding temperature) to 90 C with a heat exchanger to be pasteurized. The heat requirement of the system is met by converting the saturated steam at 127.0 ºC into a saturated liquid at the same temperature. Since the pear juice has 20 Brix, calculate the amount of steam required for this process (kg steam / kg pear juice). Note: There is a heat loss of 10% of the energy required for heating the fruit juice in the system.