Steam enters a turbine stage with an enthalpy of 3628 kj/kg at 70 m/s and leaves the same stage with an enthalpy of 2846 kj/kg and a velocity of 124 m/s. Calculate the power in KW if there are 5 kg/s steam admitted at the turbine throttle.

Steam enters a turbine stage with an enthalpy of 3628 kj/kg at 70 m/s and leaves the same stage with an enthalpy of 2846 kj/kg and a velocity of 124 m/s. Calculate the power in KW if there are 5 kg/s steam admitted at the turbine throttle.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Related questions

Q: Q4. What is the benefit of specific speed in a water turbine designs.

A: A turbine is a device that converts the kinetic energy of a fluid, like water, steam, air, or…

Q: If number of vanes on turbine is more than required, it will the work produced by the turbine. O…

A: 1.If number of vanes on turbine is morethan required, it will ..................... the work…

Q: A turbine running at 400 rpm has a specific speed of 160 rpm and head available is 41 m. If the…

A: GivenN=400rpmNS=160rpmH=41mP=200kW

Q: Steam flows through an adiabatic turbine at the rate of 100 lb/min with AK = 0 and Q=0. At entry,…

A: First law of thermodynamics First law of thermodynamics states that the energy can not be created or…

Q: The peripheral speed of the rotor of impulse turbine is (300m/S) and the absolute velocity of air at…

A: For solution refer below images.

Q: QI: If the overall efficiency of the system and turbine in the figure below is 80 percent. What…

A: Solution:

Q: 6. A pump is delivering water from the surface of a lake to a tank 20m above at a rate of 70L/s…

Q: Water is fed to an inward flow reaction turbine, running at 180 rpm with a velocity of flow of 3…

Q: Steam enters a turbine with an enthalpy of 1292 BTU/lb and leaves with an enthalpy of 1098 BTU/lb.…

Q: Q1. What are the types of water turbines with an example for each type? Q2. What is the difference…

A: The different types of water turbines are mentioned below:

Q: 28. A centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specific…

Q: A turbine is to be built in the south of Jordan for electrical power plant station. As a consultant…

A: Given,

Q: Q17. Calculate the power required to drive the compressor. If the inlet pressure, temperature and…

Q: For a single stage impulse turbine with rotor diameter of 2 m and a speed of 3000 rpm when the…

A: Given:Rotor diameter, D=2 mSpeed, N=3000 rpmNozzle angle, α=20o

Q: Centrifugal pump impeller runs at 950 rpm. Its external and internal diameters are 500 mm and 250…

A: Given: The speed of impeller, N = 950 rpm The external diameter of impeller, D = 500 mm The internal…

Q: B) Calculate the efficiency of a water turbine if the available head at the turbine inlet is 40 m,…

A: Given data:

Q: Q1// the velocity of steam at inlet to simple impulse turbine is 1000 m/s and the nozzle single is…

A: Given dataVelocity V1= 1000m/secBlade speed Vb = 400m/secNozzle angle α = 200To determine Blade…

Q: A single stage impulse turbine with a diameter of 120 cm runs at 3000 rpm. If the blade speed ratio…

A: Given, Diameter of turbine = D = 120 cm = 1.2 m Rotational speed of turbine = N = 3000 rpm Blade…

Q: Q. The velocity of steam at inlet to simple impulse turbine is 1000 m/s and the nozzle angle is 20%.…

Q: Que 4.35. A reaction turbine is revolving at a speed of 200 rpm and develops 5886 kW SP when working…

Q: 2. A hydraulic turbine receives water from a reservoir at an elevation of 100 m above it. What is…

A: Given: H=100 mP=50 MW=50×106J/s

Q: A centrifugal pump driven by a 160-hp motor rotating at 2400 rpm is used to pump 70°F water in a…

Q: Steam enters a turbine 80 lbs of steam per minute with an enthalpy of 1700 BTU/1lb and velocity of…

A: Given Data Mass of the steam, m=80 lb/min=1.34 lb/sec Inlet enthalpy, h1=1700 BTu/lb Outlet…

Q: A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated…

Q: Q2// A single row impulse turbine develops 2.3 MW at a blade speed of 105 m/s using 52 kg of steam…

A: given we have , Power develpoed by turbine =2.3 MW Mass flow rate (m) of steam = 52kg/sec and we…

Q: steam turbine developed 2372.20 hp when its inlet condition is 1300 BTU/lb enthalpy and 400 ft/s…

Q: A Kaplan turbine runner has a diameter of 5 m, and the turbine/generator assembly has an efficiency…

Q: A water pump is located where g = 31.5 ft/s? discharges water with a specific weight of 61 lb/ft? at…

Q: 30m T -2 75cmØ

A: Given data: The diameter value is, d=75 cm=75 cm×1 m100 cm=0.75 m. The power developed by the…

Q: Water flowing at 0.5 m³/min enters the turbine of a micro hydroelectric generator and delivers a…

Q: A 26-kW motor with 78% efficiency drives a centrifugal pum p delivery 68 L/s against a head of 24 m.…

Q: 4) State briefly why a Pelton turbine is an impulse turbine.

A: In impulse turbine there is jet of nozzle or series of nozzle which converts the potential energy of…

Q: 3.1 The Vertical-Shaft Francis Turbine has an overall efficiency of S90% and runs at 7.14 rev/sec…

Q: A boiler requires 100 000 m3/hr of standard air. The mechanical efficiency of fan to be installed is…

Q: A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated…

A: Given data as per question Pipe inside diameter =3 in Flow rate =150 gal/min The overall efficiency…

Q: 6.1 A centrifugal blower operating at 15,000 rpm compresses air from 68°F and 14.7 psia to 10 psig…

Q: Water from a pressurized tank enters a horizontal pipe at a velocity of 2.5 m/s and 12 kPag. At the…

A: Given that, P1= 12 KPa = 12000 Pa( gauge pressure) V1= 2.5 m/s Pipe is horizontal so, Z1=Z2 P2…

Q: of the blade velocity at runner inlet. The blade throughout the blade passage and is equal to half…

Q: 4. to convert the kinetic energy of water into the mechanical shaft energy. Water enters the…

Q: Water enters a pump at 350 kPa at a rate of 1 kg/s. The water leaving the pump enters a turbine in…

Q: A pump has a total (manometric) head of 12.1 m. The radial velocity through the pump is constant at…

Q: indicate the free body diagram A turbine is located at an elevation 200 m below that of the surface…

Q: in a steam turbine, the steam enters the wheel through a nozzle with velocity of (520m/sec) and at…

A: Since you have asked questions with multiple parts we will solve the first three parts for you if…

Q: team at 14 bar and 588.15K enters a turbine through a 75mm diameter pipe with a velocity of 3m/s.…

Q: Water is fed to an inward flow reaction turbine, running at 180 rpm with a velocity of flow of 3…

Q: A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated…

Q: 5. What is the overall efficiency of a pump driven by an 11 bhp power source that delivers fluid at…

Q: An axial flow pump with an impeller rotor diameter of 30 cm handles water at a rate of 2.7 m*/minute…

A: According to the information we have a 30-cm axial flow pump that handles a rate of 2.7 m */ minute…

Question

Pls. Answer this thank you!Steam enters a turbine stage with an enthalpy of 3628 kj/kg at 70 m/s and leaves the same stage with an enthalpy of 2846 kj/kg and a velocity of 124 m/s. Calculate the power in KW if there are 5 kg/s steam admitted at the turbine throttle.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Derive the expression for specific speed of a turbine.
Steam enters a turbine with an enthalpy of 1292 BTU/lb and leaves with an enthalpy of 1098 BTU/lb. The heat loss is 13 BTU/lb. What is the work done per BTU/min and in hp for a flow of 2 lb/sec? Provide complete solution, with diagram
NOTE THE ANSWER SHOULD BE 10.75m3/s Find the flow rate of water through the sytem shown for the turbine to produce 20 kW. Neglect friction in your calculations NOTE: THE ANSWER SHOULD BE 10.75m3/s
3.21) An axial flow compressor has an overall pressure ratio of 4.0 and mass flow of 3 kg/s. If the polytropic efficiency is 0.88 and the stagnation temperature rise per stage must not exceed 25 K, calculate the number of stages required and the pressure ratio of the first stage. Assume equal temperature rise in all stages. If the absolute velocity approaching the 1st stage rotor is 165 m/s at an angle of 20° from the axial direction, the work done factor is 0.83, the velocity diagram is symmetrical, and the mean diameter of the 1st stage rotor is 18 cm, calculate the rotational speed and the length of the 1st stage rotor blade at inlet to the stage. Ambient conditions are 1.01 bar and 288 K. [7,1.273, 356 rev/s, 19.45 cm]
Pls answer thank you! Steam enters the turbine at the rate of 2.5 kg/s with enthalpy of 3200 kj/kg and exhaust enthalpy of 1100 kj/kg . Steam is extracted from the turbine at the rate of 1 kg/s for heating purposes with enthalpy of 2750 kj/kg. What is the turbine work in KW.
A steam turbine developed 2372.20 hp when its inlet condition is 1300 BTU/lb enthalpy and 400 ft/s velocity and steam flow of 200 lb/min. The exit enthalpy is 800 BTU/lb. Find the exit velocity.
A turbine receives steam at 10 MPa, 6000C and exhaust it at 0.2 MPa. (a) for the actual engine,the brake engine efficiency is 84%; the driven generator efficiency is 93% and the rated output of the generator is 30 MW. Compute the combined work, combined heat rate, and the total throttle flow for the rated power.
Derive the equation for turbine and nozzle with the help of steady energy equation by stating their assumptions.
1. As a junior city engineer of a municipality, you are tasked to design the specifications of the pump with 3650 cu.m/day. The water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open 4l Pressure reservoir Tank 70 m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is a.) 200 mm b.) Suction pressure of the pump in kPa (Pressure at pt. 2). c.) Velocíty head at pt.3 to 4 if the diameter of the pipe is 150 mm d.) Discharge pressure of the pump in kPa (Pressure at pt. 4). Assume atmospheric pressure at the pump. If an air vent is installed at the pipe just right before the pressure tank with diameter of 20 mm, what is the velocity of discharge in m/s? The height of the pressure tank is 12 m, what is the flowrate in cu.m/hr at pt.5 if the diameter of the pipe is 150 mm? e.) f.)
4. to convert the kinetic energy of water into the mechanical shaft energy. Water enters the turbine, at the inlet, with the velocity Vin = 40m/s and the mass flow rate m=1,000kg/s. Water exits the Vi,z40ms turbine with a negligible velocity, say, Vout = 0 m/s.The efficiency of m - loooly/s Figure on the right shows a hydraulic turbine designed HzO HzO the turbine is 75 %. Potential energy and flow work can be ignored. 4а. Please calculate the specific kinetic energy of water entering the turbine ( ɛr or ke; in J/kg). 4b. Please calculate the rate of total kinetic energy of the water flow ( É̟ or KĖ ; in J/s or W) 4с. Please determine the mechanical power output of this turbine (Wou; in W or kW). 4d. Please determine how much mechanical energy would this turbine generate during an hour
8. A turbine passes 67.5 kg/h of steam at 200 km/h at 8 MPa and leaves at 0.5 MPa as wet steam with a speed of 90 km/h and a specific volume of 0.189 m3/kg. d. What must be the steam input conditions (T,H) to turn on a device that consumes 30 kW? and. What is the mass and volumetric flow rate of the water at the outlet? F. What is the input and output area?
Consider a turbojet engine with a thrust of 10,000-lb and an inlet diameter of 4-ft. If an airplane is equipped with this particular engine flying at Mach 0.6 at a standard altitude with an atmospheric pressure of 38,721.71-Pa. Calculate the jet velocity in fps. The jet velocity. (in fps)