State 1 for a dual combustion engine is p = 1 atm and T1= 60.3°C; r = 18; at the end constant volume combustion process the pressure is 7695 kPa, r= 1.5. Base on 1kg/cycle of a hot-air standard with k clearance, (b) p, V, and T at each corner point on the cycle, (c) WNET» (d) e, and (e} 1.31, determine (a) the percentage %3D Pm Ans. (a) 5.88% (h) 0.9443 m.0.05246 m3, 4468 kPa, 816.5 K, 1406.2 K,

State 1 for a dual combustion engine is p = 1 atm and T1= 60.3°C; r = 18; at the end constant volume combustion process the pressure is 7695 kPa, r= 1.5. Base on 1kg/cycle of a hot-air standard with k clearance, (b) p, V, and T at each corner point on the cycle, (c) WNET» (d) e, and (e} 1.31, determine (a) the percentage %3D Pm Ans. (a) 5.88% (h) 0.9443 m.0.05246 m3, 4468 kPa, 816.5 K, 1406.2 K,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Provide a long answer using necessary graphs / equations. Describe the Rankine thermodynamic cycle. What thermodynamic processes occurs? Where is the cycle used? How to improve the cycle?
1.5 Develop an expression for the thermal efficiency of the air-standard diesel cycle as a function of the compression ratio r. = V1N2 and the expansion ratio re = V4 / V3. Assume the working fluid is an ideal gas, and the volume effect of moles of gas %3D generated is small relative to the effect of heating from combustion.
can you draw and schematic and t-s fiagram for this actual reheat rankine cycle State 1: Status: Saturated Liquid 30 kPa From Table A5 when ʋ1=ʋf = 0.001022 m3/kg h1=hf = 289.27 kJ/kg State 2a: Status: Compressed liquid P2s=PH= 6000 kPa h2a= 296.04 kJ/kg [ WP, ise= Wpact = State 3 Status: Superheated Steam P3=PH=6000kpa T3=Tmax= 550°C From Table 6A, When = 6000 kPa and =550 =3423.1 kJ/Kg =6.8826 kJ/Kg⸼K
p88#5. while the pressure remains constant at 689.5 kPa the volume of a system of air changes from 0.567m^3. what are the (a)internal energy,(b) enthalphy ,(c) Q, (d) entropy, (e) if the process is nonflow and internally reversible,what is work?
Question C . Options A. Subsonic Nozzle B. Expansion Tube C. Diffuser D. Supersonic Nozzle
Thermodynamics subject power cycles. Show the ts diagram and complete and step by step solution. Box the final answer.
Example 7: Throttling Water is throttled from 1 bar, 60 °C, to 0.5 bar, and to 0.1 bar. In each case calculate the exit temperature and the entropy generation. ab k 11°C Mostly cloudy Esc FnLock 1 1 2 Q FI A Z @ 2 W S # 3 X Saluting ‒‒ - E D Q Search F4 $ 4 C R F V 6 G V B & 7 H FB U N * 8 J F9 1 ( 9 F10 K M O F11 O P JE 3 ; + ( O [ 4x 11 ? 1 9:49 AM 11/1/2023 Delete A Backspace 0 En
Thermodynamics subject power cycles. Show the ts diagram and complete and step by step solution. Box the final answer.
During the compression stroke of a certain gasoline engine, the pressure increases from 1.00 atm to 19.0 atm. The process is adiabatic and the air-fuel mixture behaves as a diatomic ideal gas. (a) By what factor does the volume change? Vfinal = Vinitial (b) By what factor does the temperature change? Tinal = Tinitial Assume the compression starts with 0.016 mole of gas at 28.5°C. (c) Find the value of Q that characterizes the process. (d) Find the value of AEnt that characterizes the process. (e) Find the value of W that characterizes the process.
Steam enters a control yolume that has one inlet and two exits. At the inlet (location 1) with a diámeterof 5.2 cm, the Steam has 100 bar , 360°C , and as mass flow rate of a Rg/sec. Through one exit (location 2), 15.% of the incoming mass flow rate Teaves the Control volume and the remainder leaves through the otner exit (locatión 3). For steady state opeaton, calculake the mass flow rate at locatlon 3 in kg/sec using 5 Signifigant figiures. रप्री द
Net work input q in cop
The last 3 parts B,D,E