square tied column 400mm on a side carries factored dead load of 800 kN and a factored live load of 1500 kN. Using fc'=27.6 MPa, fy=415 MPa, lateral tie diameter of 10mm, clear cover of 40mm determine the required number of 28mm diameter longitudinal bars, determine the required spacing of lateral ties.

square tied column 400mm on a side carries factored dead load of 800 kN and a factored live load of 1500 kN. Using fc'=27.6 MPa, fy=415 MPa, lateral tie diameter of 10mm, clear cover of 40mm determine the required number of 28mm diameter longitudinal bars, determine the required spacing of lateral ties.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the spacing of rivets in mm.
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa.
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the maximum positive bending moment in the beam in kN-m.
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the maximum flexural stress at 1 m from the support at D to E in MPa.
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the maximum flexural stress experienced by the beam in MPa.
Situation: A column with circular ties shown carries a dead load of 1000 kN and a live load of 520 kN. Use f'c-28 and fy=420 MPa. U=1.2D+1.6L. Which of the following most nearly gives the safe diameter of the column if p = 0.0185? a. 340 mm b. 380 mm C. 400 mm d. 450 mm Which of the following most nearly gives the required minimum diameter of main bars if the diameter of column is 400mm? a. 25 mm b. 32 mm c. 28 mm d. 20 mm
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the moment of inertia of the section in x10^6 mm^4
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the location of the centroid, in mm, from the left of the section.
Assume a concrete cover or 40mm, 10mm stirrups and clear distance between layers of 25mm. For Problem 9 and 10, determine the concrete and steel stresses at the fixed Support C 1.6P (6 Section at C Wo 28 kN/m W- 11 kN/m Pa 112 kN Pu = 52 kN 3.3m 1.5m 3.9m 8-36mmo 4.6m f- 25 MPa Grade 40 rebars d' 75mm A d 585 mm 4-36mm b-300mm
10mmØ. two legged stirrups. The beam width is 300mm, height is 700mm and effective depth is 630mm. Use fc'=24Mpa and Grade 60 stirrups. Determine the shear reinforcement spacing of the beam shown within and beyond 2h from the support using Pu = 250 kN Wu = 70 kN/m 600 kN-m 500KN-m VBA VAB 3.0 m 4.0 m VBA - 44.1, Vu at 2h = VBA-98 Vuat d =
The span of single reinforced rectangular beam whose dimensions are given below for cross section, Cover value will be taken as 35 mm. C25/30 – S420 a)Neutral axis depth (c) and equivalent pressure block depth (a) calculate. b)By calculating the area of tensile reinforcement to be used and the percentage of reinforcement Make the necessary investigations. c)Calculate the moment of bearing power.
Draw BMD and SFD for the beam shown below: 8 kN w 2 kN/m A 3 m B. 9 m 3 m Rp D.