spur- RW, unase squirrel-cage 1e auiuun, 1244 rev/min. The load is smooth, providing a reliability of 99.9 % at 109 revolutions of the pinion. Gearing space is meager. Use pinion materials to be Nitralloy 135M, grade 2 steel and nitrided through-hardened grade 1 steel material to keep the gear size small. The gears are heat-treated first then nitrided. Consider temperature factor is 1.1 for 250 OC.

spur- RW, unase squirrel-cage 1e auiuun, 1244 rev/min. The load is smooth, providing a reliability of 99.9 % at 109 revolutions of the pinion. Gearing space is meager. Use pinion materials to be Nitralloy 135M, grade 2 steel and nitrided through-hardened grade 1 steel material to keep the gear size small. The gears are heat-treated first then nitrided. Consider temperature factor is 1.1 for 250 OC.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 2-tooth ge A parallel-shaft gearset consists of an pinion has a left-hand helix angle of 25°, a…

Q: A gearbox is needed to provide an exact increase in speed, while minimizing the overall gearbox…

A: Given:Achieve an exact output speed of 13250 rpm while minimizing gearbox size and transmitting 18…

Q: aight Spur geard, having 20 involu telk full de pth teerh is to halre tvanjmitted Power 12 KW at 3ne…

A: assume y

Q: A 17-tooth 20° pressure angle spur gear rotates at 1800 rev/min and transmits 4 hp to a 52-toot…

A: dp=NpPd=1710=1.7 indG=5210=5.2 inV=πdp.np12=π×1.7×180012=801.1 ft/min

Q: A 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressure…

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A: (a) The total number of gear teeth on pinion and wheel: Ztotal = 83 teeth. (b) The number of teeth…

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A: Given data Reduction ratio = 2.32 Centre distance = 83 mm Module = 2mm Find the output speed .

Q: pitch of 4 teeth/in, a 2 inch face, 20 teeth, and a pressure angle of 20° with full depth teeth. The…

A: the term moderate applications seems to imply that the gear can be rated by using the yield strength…

Q: A transmission system with a pair of beveled gears has the following data: 25° gear angle, 20° full…

A: Bevel gears are the gears meshed together in order to achieve maximum efficiency through minimal…

Q: 13-34 A compound reverted gear train is to be designed as a speed increaser to provide a total…

Q: Q/A steel spur pinion and gear of grade 1 have a diametral pitch of 11 teeth/in , shaped profile…

Q: A steel gear is to be mounted on a solid steel shaft using an interference fit H6/s8. The gear has…

Q: A 20° spur pinion with 20 teeth transmits 120 W to a 36-tooth gear. The pinion speed is 100 rev/min,…

Q: 3. Specify a maximum key length for a gear to be mounted on a shaft with a 2.00 in diameter. The…

Q: A pair of straight bevel gears drives the vertical drilling machine. The approximate speed reduction…

Q: wo spur gears are to have a ratio of 9:3 and a 7mm module. If the center distance is to be…

Q: ulate the number of te

Q: Design a two-stage compound spur gear train for an overall ratio of approximately 17+ID:1. Specify…

A: overall ratio=17+0071=241

Q: 02 The fellowtng aata relate to a pair of 20 molute gears m mezh: 3ochie-6 mm Number of teetk on…

Q: A pair of steel gears have a design life of a million cycles. They have 20° full-depth teeth with a…

A: Pitch diameter , d=NPdd==208=2.5Velocity V=πdn12V=π X 2.5 X 200012V=1308 ft/minVelocity factor for…

Q: (b) Determine the safe power which can be transmitted by a pair of helical gears, 20° full depth,…

A: Gears are the two rings having teeth on it which are meshed together to transmit the power. They are…

Q: A gearbox is needed to provide an exact increase in speed, while minimizing the overall gearbox…

A: Given:The power required to transmit gearbox is .The output speed is .The input speed is .Formula…

Q: A 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressure…

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A: Given data Reduction ratio = 2.32 Input torque = 100N-m Input speed = 3000rpm Efficiency = 98% Find…

Q: Qv quality number for camberless straight bevel pinion gear with 20 teeth and a modulus of 4 mm is…

A: Pinion teeth (Tp)=20Modulus (m)=4mmQuality number (Qv)=6Hardness (HB) = 300Rotated gear teeth (Tr) =…

Q: What is the total force exerted by the pinion on the gear? Report your answer in lbf.

Q: handwritten

Q: The normal, transverse, and axial circular pitches The transverse diametral pitch and the transverse…

A: Given: No of teeth on pinion= 19 No of teeth on gear =57 helix angle =30 Normal pressure angle =20…

Q: *:A 18 teeth 20°normal pitch angle helical pinion with a right-hand helix angle of 30° and The…

A: Contact stress is stress which produces due to pressure or forces which does not exceed the elastic…

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A: Since you have asked only specific question so i answer only the subpart i for you. Given Data The…

Q: Two spur gears are to have a ratio of 9:3 and a 7mm module. If the center distance is to be…

A: Module(m) = 7 mmCentre Distance(CD) = 200 mmGear Ratio (GR) = 9:3 = 3:1GR = (T/t) = 3:1T = Teeth on…

Q: esign a spur gear drive for a motor running at 1500 rpm transmitting 15 kw power to a lower speed…

A: given data; ⇒running speed (N)=1500rpm⇒power(P)=15KW⇒speed reduction ratio (cv)=2.33⇒starting torque…

Q: - number of teeth ower of 3 kW at 2

Q: A pair of parallel helical gears has 14.5° normal pressure angle, 6 diametral pitches and 45 helix…

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Q1
Design a 4:1 spur-gear reduction for a 59 kW, three-phase squirrel-cage induction motor running at
1244 rev/min. The load is smooth, providing a reliability of 99.9 % at 109 revolutions of the pinion.
Gearing space is meager. Use pinion materials to be Nitralloy 135M, grade 2 steel and nitrided
through-hardened grade 1 steel material to keep the gear size small. The gears are heat-treated first
then nitrided. Consider temperature factor is 1.1 for 250 0C.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step by step

Solved in 7 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

O It is required to design a pair of spur gears with 20° full-depth involute teeth. The input shaft rotates at 720 rpm and receives 5 kW power through a flexible coupling. The speed of the output shaft should be 144 rpm. The pinion as well as the gear are made of steel Fe 410 (S = 410 N/mm). The service factor.for the application is 1.25. The gears are machined to meet the specifications of Grade 6. ut [LO 6, 7] (i) Assume suitable number of teeth for the pinion and the gear. (ii) For preliminary calculations, assume the pitch line velocity as 5 m/s and the factor of safety as 2. Estimate the module and select the first preference value of the module. (iii) Using this value of the module, calculate the pitch circle diameters of the pinion and gear and the face width. (iv) Determine static load and the dynamic load by Buckingham's equation. Also calculate the beam strength and the correct value of factor of safety based on beam strength. (v) Using a factor of safety of 2 for wear…
ExJA 20° straight-tooth bevel pinion having 14 teeth and a diametral pitch of 6 teeth/inch drives a 32-tooth gear. The two shafts are at right angles and in the same plane. The pinion is to transmit 1800 rpm and transmitting 50 hp. Find: a) the cone distance; b) the pitch cone angles; c) the pitch diameters; and d) the tooth loads of the pinion. Solution: (To be discuss during the lecture period)
Do it fast
A pair of gears with 20° full-depth teeth are to transmit 15hp at 1750 rpm of the 4-in pinion; velocity ratio desired is about mw= 4; intermittent service. Use a strength reduction factor of about 1.4, with the load at the tip and teeth carefullycut. A.Determine the diametral pitch, B. face width, C. and tooth numbers if the material is cast iron, class 25
For each problem demonstrate your answer using autocadd software. 10.2 For the gear pairs given below and meshing at their correct center-to-center distance, determine whether any interference is present. Assume that the addendum is 1/P in each case. (spur gear) 10.21. 25° involute gears having 30 and 60 teeth. (P = 4)
What is the radial load exerted by the pinion on the gear? Report your answer in lbf.
Q12:- Two involute gears of 20° pressure angle are in mesh. The number of teeth on pinion is 20 and the gear ratio is 2.0. The module= 5 mm and the pitch line speed is 120 cm/sec and assuming the addendum as standard and equal to one Find:- (a) the angle turned through by when one pair of teeth is in mesh and (b) the maximum sliding velocity. module.
A parallel helical gearset consists of a 21-tooth pinion driving a 63-tooth gear. The pinion has a left-hand helix angle of 20°, a normal pressure angle of 14 1/2, and a normal diametral pitch of 10 teeth/in. Find: (a) The normal, transverse, and axial circular pitches (b) The transverse diametral pitch and the transverse pressure angle (c) The addendum, dedendum, and pitch diameter of each gear Attach File Browse My Computer
14-21 A 20° spur pinion with 20 teeth and a module of 2.5 mm transmits 120 W to a 36-tooth gear. The pinion speed is 100 rev/min, and the gears are grade 1, 18-mm face width, through-hardened steel at 200 Brinell, uncrowned, manufactured to a No. 6 quality standard, and considered to be of open gearing quality installation. Find the AGMA bending and contact stresses and the corresponding factors of safety for a pinion life of 10° cycles and a reliability of 0.95.
Asap
A 17-tooth 20° pressure angle spur pinion rotates at 1800 rev/min and transmits 4 hp to a 52-tooth disk gear. The diametral pitch is 10 teeth/in, the face width 1.5 in, and the quality standard is No. 6. The gears are straddle-mounted with bearings immediately adjacent. The pinion is a grade 1 steel with a hardness of 240 Brinell tooth surface and through-hardened core. The gear is steel, through-hardened also, grade 1 material, with a Brinell hardness of 200, tooth surface and core. Poisson's ratio is 0.30, Jp = 0.30, JG = 0.40, and Young's modulus is 30(10°) psi. The loading is smooth because of motor and load. Assume a pinion life of 108 cycles and a reliability of 0.90, and use YN = 1.3558N-0.0178, ZN = 1.4488N-0.023. The tooth profile is uncrowned. This is a commercial enclosed gear unit. (a) Find the factor of safety of the gears in bending. (b) Find the factor of safety of the gears in wear. (c) By examining the factors of safety, identify the threat to each gear and to the…
p sa 15. A straight bevel gear pair has the following data: 50; P¿ 10; and 20° pressure angle. If the gear pair is transmitting 3.5 hp, compute the fore- es on both the pinion and the gear. The pinion speed is 1250 rpm. The face width is 0.70 in. Compute the bend- ing stress and the contact stress for the teeth, and specify a suitable material and heat treatment. The gears are driven by a gasoline engine, and the load is a conveyor provid- ing moderate shock. Assume that neither gear is straddle nounted. N₂ No = 25; No J (M