Solve the given problems. 4. Determine the x, y, z components of reaction at the ball-and-socket joint A and the tension in each of the wires, if the load weighs 100kg. 1.5m 1m. B 1m. 1m G 1m 1m E 2m

Q: Situation 3. The system shown anchors a stanchion of a cable-suspended roof. If the tension in cable…

A:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: Given:P=38 NQ=52 NS=64 NT=31 Nα=15°β=65°θ=25°

Q: the structure compared with the applied loads. Is the knowledge of the size of the structure…

A: First draw the free body diagram as, Now from the free body diagram of the given truss  Now…

Q: The boom shown has a negligible weight and supports the 1000 N load. А 60° 1000 N 7.1 Find the…

A:

Q: A 363.8N horizontal steel shaft is suspended by a vertical cable from A and by a second cable BC…

A: Consider the free body diagram shown below for the given system.

Q: If P₁ = 5.1 lb, P2 = 5.1 lb, P3 = 10.1 lb, and dc = 3 m, determine the reaction at E and the…

A:

Q: Two cylinders are being supported by the wires shown in the figure. Determine the following:   1.1…

A: Given :-  To Find:-  1.1 The tension developed in wire BC required for equilibrium of the 13.6-kg…

Q: Using the principles of equilibrium of Non-concurrent forces.

A: The free-body diagram is:

Q: Determine the reactions for the frame shown in Fig., by the method of least work. ElI is constant.

A: Structure is supported by fixed supports at point A and point D. Let Horizontal reactions at point A…

Q: Problem 1: Determine the reaction force at the roller F for the frame loaded and supported as shown.…

A: According to the given data, thereis a loading structure given ABCDEF We need to findreaction at a…

Q: Problem 5. The cable and boom system shown support a load of 755 N Determine the tensile.

A: given:

Q: Determine the minimum initial velocity and the corresponding angle at which the ball must be kicked…

A: Let the initial position of ball x-y coordinate  X-component of the ball initial velocity v0 is…

Q: Solve the following problems completely. Include the FBD with proper labels. 1. The truss is…

A:

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

A:

Q: Determine (a) the horizontal and vertical components of the reaction that pins A and B exert on the…

A:

Q: Refer to the diagram. The roller at A is in a smooth slot. Determine the reactions at A and O.

A: for vertical equilibrium F1sin 55 + Ay = Ry1.258 * sin 55 + Ay = Ry   For Horizontal Equilibrium…

Q: A member (AC) is supported by a pin at A and a roller at B. The horizontal component of reaction at…

A: Let us draw the reaction supports

Q: n forces in the pin A and roller B,

A:

Q: 4. A truss is loaded as shown. The reactions at A and K are each 3.6 kips upward. Determine the…

A: Answer: The force in the member GH is -1.5882353 kips (Compressive).

Q: PROBLEM 3: Determine the tension in each of the three ropes supporting the crate. 2 ft 4 ft 4 ft B y…

A:

Q: The bar is pin connected at B and is supported by rollers at C. Neglecting the weight of the bar,…

A:

Q: Two traffic signals are attached to the_36 ft support cable at equal intervals as shown. Determine…

A: Please find the solution below

Q: Q1: Determine the reactions at the roller F and pin E for the frame loaded as shown. 0.2 m 0.2 m 0.3…

A:

Q: PROBLEM 2 For the figure shown, determine the following if the mass of the person is 50kg and the…

A: Dear student, as per the guidelines of Bartleby we are authorized to answer the first question only.…

Q: Problem #1: Distributed Loading Determine the reactions of the pin at C and the tension in the rope.…

A: Determine the reactions of the pin at C and the tension in the rope.

Q: 4. A pipe strut BC is loaded and supported as shown. The strut has a uniform cross section nd a mass…

A: Answer: (a) The tension in the coal is 498.1 N. (b) The reaction at support C is 898 N.

Q: The homogeneous 100-kg sign is suspended from three wires. Find the tension in each wire. A 2 m B y…

A:

Q: The tension in cable AD is N.

A:

Q: 600 lb C 18 25 750 lb-ft B 10 900 lb| Dimensions in inches

A:

Q: is The left support of the cable shown in Fig. located 40 ft below the right support. The cable is…

A: For the given cable, Span length, l=400 ftDifference between level of both support, d=40 ftsag of…

Q: The smooth uniform rod ABAB is supported by a ball-and-socket joint at AA, the wall at BB, and cable…

A: given-            mass of rod=19kg to be determine-                          1- tension in the…

Q: 2. Determine the reactions at the support. (Final answers in kN and kN-m, 3 decimal places) 8.y kN/m…

A:

Q: The homogeneous 600-lb plate is suspended from three cables. Determine the tension in each cable.…

A: Given: Weight of the plate is 600 lb.

Q: Stiller Düzenlem Üst 2) A uniform brass plate with area of 18 x 18 m? has mass of 41 kg which is…

A:

Q: Q.4) Determine the tensions in the three cables supporting a weight of 180 N as shown in figure…

A: Let us take origin as O. FBD:   From figure, O = (0,0,0) A = (4,-8,5) B = (-6,-8,5) C = (0,8,5)…

Q: Four sets of flexible cables, spaced at 120° intervals, are used to stabilize a 400-ft…

A: Draw the free body diagram of the section containing point A: The axial force transmitted through…

Q: Problem 5: Determine the roller reaction (in kips) at A of the frame shown. 5 kip 7 kip 10 kip 2 kip…

A:

Q: A 15 m long boom of negligible weight is supporting a 700 N load at point F and a 350 N load at B,…

A:

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.