Solve by joint method. Should correct 30 KN12-1M. Determine the forces in the members of the truss in Figure 12-11M.30 KN↓A60 KNtoH60 kN↓E4 at 3 m 12 m60 KNJ30 kN↓3mER

Given Data Determine the forces in each member using Method of Joints.

Answered: Solve by joint method. Should correct

Engineering

Civil Engineering

Solve by joint method. Should correct

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Create a graph of the shear and bending stresses at the fixed support (B) over the cross- section.…

Q: complete solution and drawing. if u can please add some explanation thankyou

Q: A material of the section is 2.5cm Calculate the least radius of gyration. Calculate the slenderness…

Q: While analyzing a plane truss using method of joints, which of the statement is true Select one: a.…

A: Option A is correct We begin the analysis of a joint where at least one known load exists and not…

Q: (b) A hollow rectangular section has outside dimensions 30cm x 15cm. The material of the section is…

A: given- outside dimension b=30 cma=15 cmthickness t=2.5 cminside dimensionb1=(30-2.5)=27.5…

Q: By internal couple method, what is the maximum stress on the steel side of the transformed section?…

A: Given data: m=9

Q: 20 mm) 80 mm 20 mm) 120 mm A square box beam is made of two 20×80-mm planks and two 20x120-mm planks…

Q: Determine the member stresses in members AB, AC, AD, BC, and BD if the cross-sectional area for all…

A: As per guidelines we need to answer only first question so please repost rest questions separately

Q: The beam is constructed from two boards fastened together at the top and bottom with two rows of…

A: Consider the following figure. The internal shear force is V=10 kN. The allowable shear stress is…

Q: III, The section size and reinforcements of a simply supported reinforced rectangular beam is shown…

Q: Bending stress is directly proportional to the width of a section. True False

A: Bending Stress = M y / I Bending stress is directly proportional to bending moment. It is directly…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: A wooden beam is fabricated from three boards to form a double-tee cross section. Assume L1 = 14…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: A wooden beam is fabricated from one 2 × 10 and two 2 x 10 dimension lumber boards to form the…

Q: 6200 N 4.5 m B O 2 m 1.5 m to 4.5 m & E b.) Determine the forces in members AB, BD and DE by the…

A: The given figure is shown below:

Q: Show complete solution (show how you achieve the member forces , e.g method of joints/method of…

A: Given : 2D truss solve using consistent deformation EI = constant

Q: From the figure, find the force in member BG using methods of joints *use 3 decimal place in…

A: Find the reactions Take moment about A∑ MA=0Ey12-12009-15003-75032=0Ey=1368.75NTake equilibrium…

Q: It is obtained by fixing 4 wooden planks to each other with nails. given as a cross section. 2…

A: Given:- The dimension of the two vertical planks = 20 mm X 80 mm The dimension of the two horizontal…

Q: Determine the member stresses in members AB, AC, AD, BC, and BD if the cross-sectional area for all…

Q: STD_PCS Problem 1_Analysis of Complex Truss Solve the complex truss (similar to the truss of the…

Q: Using the method of joints. Round off your answer into two decimal places. Eliminate all the…

A: In the method of joint, each joint is analyzed separately. While applying the method of joints, it…

Q: 1- A 7000 N force is applied horizontally at joint B of the three-element, pin-joined truss shown…

Q: If B=650N, determine the: •Direction of the line of action of the resultant force on each member due…

A: Determine magnitude of the resultant force on each member due to pin A

Q: Determine the location of the neutral axis (mm) from the extreme tension fiber of a beam if the…

A: given, Strain in Concerte = 0.003 Strain in steel = 0.0056 Effective depth of the beam (d) = 570mm…

Q: 30KN A 60kN B 60KN C H 12.0 m 60kN DE G 30kN M tot 3.0 m

A: Method of section:- This method can be used to calculate the specific force in member of a truss.…

Q: Problemt The detail of a truss at the support is glued as shown. Given: shearing stress = 800 kN/m?…

Q: What could be the problem with the knot? E. How would you change the knot?

Q: This "I-shaped" cross-section is often used for beams because the moment of inertia about the…

A: Given data Find moment of inertia about strong axis (I) using subtractive method or additive…

Q: AZ B Ф q С

Q: Subject : Mechanics of materials Give me right solution urgent please If the applied shear force V…

A: centroid of section: YBottom¯=7×2×(3+22)+2×3×2×327×2+2×3×2=2.846 inch Moment of…

Q: Using the method of joints. Round off your answer into two decimal places. Eliminate all the…

A: According to our company policy we are bound to solve only first 3 partsPlease paste another part…

Q: A bearing pad is a device which is used to support a bridge or other heavy structure in a way that…

A: Step 1: To determine the Average shear stress: Average shear Stress, Ʈav = Fh /(a x b)…

Q: No explanation required Beam CB has some applied forces and moments such that the internal loadings…

Q: The section shown has dimensions H=1.4" & b=1.6", and is subjected to moments M1=6 in-kips & My=23…

Q: A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement…

A: Given: The width of the beam is 280 mm. The effective depth is 500 mm. The area of reinforcement is…

Q: The crowbar is subjected to a vertical force of P = 27 Ibat the grip, whereas it takes a force of F…

A: Given : P = 27 lb at the grip and F = 160 lb at the claw To Find : Moment of force P about A Moment…

Q: Help me answer & find the solutions pls.

A: Step 1:Step 2:

Q: Determine the forces in members CD, GD, GH. use method of sections. *use 3 decimal place in rounding…

A: Find the reactions at the right supportTake moment about A∑ MA=0Ey12-12009-15003-75032=0Ey=1368.75N

Q: Calculate the depth of compression block of the section in PART A in mm.0

A: Given,

Q: Using the method of joints. Round off your answer into two decimal places. Eliminate all the…

Q: An area of the shape and dimensions show has been selected for strength analysis. Determine the…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

Solve by joint method. Should correct

30 KN
12-1M. Determine the forces in the members of the truss in Figure 12-11M.
30 KN
↓
A
60 KN
to
H
60 kN
↓E
4 at 3 m 12 m
60 KN
J
30 kN
↓
3m
ER

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step by step

Solved in 7 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

can someone help?
20 mm) 80 mm 20 mm) 120 mm A square box beam is made of two 20×80-mm planks and two 20x120-mm planks nailed together as shown. Knowing that the spacing between the nails is s= 30 mm and that the vertical shear in the beam is V=1200 N, determine (a) the shearing force in each nail,
THEORY OF STRUCTUREWrite the correct answer on the space provided.Round off all answers to FOUR (4) decimal places. SHORTCUT IF NECESSARY100% UPVOTE GUARANTEE IF THE ANSWER IS CORRECT.
Need help with this
Consider a long slender beam subjected to an end shear, V = 500 N. The cross section is made up of three separate pieces fastened together using a nail on the top and bottom. If the nails are spaced at intervals, s = 25 mm determine the shear force in each nail. nail S 20 mm (typ) 20 mm 100 mm 20 mm 100 mm cross section
The steel truss shown carries a downward vertical load of 14 kN at joint B. The diagonal members of the truss have an area equivalent to 250 mm^2, and the horizontal members are 300 mm^2. With the given conditions calculate the: a) Horizontal Deflection at E in mm b) Vertical Deflection at D in mm Esteel = 200 GPa
Please write the solution on paper. Additionally, please use "method of joints" when solving for subpart c.
A post having a hollow, circular cross sectionsupports a P = 3.2 kN load acting at the end of an armthat is b =1.5 m long (see figure). The height of thepost is L = 9 m, and its section modulus is S = 2.65x105 mm3. Assume that the outer radius of the post isr2 =123 mm, and the inner radius is r1 =117 mm.(a) Calculate the maximum tensile stress σmax andmaximum in-plane shear stress τmax at point A onthe outer surface of the post along the x axis dueto the load P. Load P acts at B along line BC.(b) If the maximum tensile stress and maximumin-plane shear stress at point A are limited to90 MPa and 38 MPa, respectively, what is thelargest permissible value of the load P?
Please help me with the following question. You can use the second photo as reference and please put the whole process and solution because I’m having a difficulty with understanding it. Thank you very much. Use Method of Sections SN=66
20 mm) 80 mm 20 mm) 120 mm A square box beam is made of two 20×80-mm planks and two 20x120-mm planks nailed together as shown. Knowing that the spacing between the nails is s= 30 mm and that the vertical shear in the beam is V=1200 N, determine (a) the shearing force in each nail,
PLEASE SHOW COMPLETE SOLUTION AND WRITE PROPERLY (Round off your answers up to 2 decimal places)
Please don't provide handwritten solution ....