SO X3 0 ** SÅ Y3 0 X2° Y20 X10 Y10 XO 1 YO 10** U1A 200 U1:8 201 U1:C A U1:0 240 U4A bar U48 LAC bar U4D Par D USA D 1221 ❖ UZA US:A D ईना A US:8 Fer 10 m3 m2 0 m1 1m0

Q: How Wheatstone bridge acts as a TRANSDUCER in barometers?

A: The different designs for pressure, load and torque sensors become a transducer with the utilization…

Q: Why is it important to know you measure current through a component and voltage across?

A: Please find your answer below in step 2

Q: Is ohm law applicable to semiconductor, insulator. Give reasons?

A: Ohm's law is a law that is associated with voltage , current and resistance. It states that the…

Q: Analyze the different semiconductor technologies, such as silicon, germanium, and gallium arsenide

A: In the given questions we need to Analyze the different semiconductor technologies, such as silicon,…

Q: semiconductors

A: Semiconductors are a key component in electronic devices. There are mainly two types of…

Q: 5. Determine the total resistance if each Ris 30. RT M

A:

Q: Explain and elaborate the  Different Components used in Electronic Circuits and how does it work?

A: Different Components used in Electronic Circuits component. Capacitor Resistor Diode…

Q: Use your own words to explain how current flow in nanotransistors.

A: Specification of Nano-transistor  Separation between gate electrode from the channel is smaller…

Q: What is DF04m? How to use in lighting dimmer system?

A: DF04m is a single-phase bridge rectifier. It has 4 pins having a peak reverse voltage of 400 V and a…

Q: Four cells each of 2.10 volt internal emf are parallel connected together to make a battery. The…

A:

Q: (a) List down TWO differences between POSITIVE and NEGATIVE lithography. (b) What are the main…

A: Given: (a) List down TWO differences between POSITIVE and NEGATIVE lithography.(b) What are the main…

Q: what is the causes of voltage drop

A: Voltage Drop: Causes  Increased resistance in a circuit, which is usually generated by an increased…

Q: Define corrosion and also explain primary and secondary briefly explanation? step by step

A: The corrosion can be referred as the process by which the metal conductors loose their properties…

Q: Three types of electric devices A, B, and C are connected in series across a 115-volt ac source, and…

A: In thid question we will find given device types with given information...

Q: What is the maximum value of the potentiometer? And What project can do using potentiometer? Explain…

A: It is asked to explain in brief about the maximum value of a potentiometer. It is aslo asked in…

Q: Why are there different batteries for various purposes? Is it possible to have an all-purpose…

A: Different material has a different electro chemicals property, & so they produces different…

Q: need a reference about Elemental Semiconductor

A: Semiconductor has a electrical properties and which is used for the devices like diodes, transistors…

Q: Describe the function of voltmeter and ammeter

A: Voltmeter and ammeter is an instrument which are used in an electrical or electronic circuits. -The…

Q: What minimum value of series resistance s required when three 10-watt, 10-volt, 1000-mA zener diodes…

A: From the Question What minimum value of series resistance is required when three 10-watt, 10-volt,…

Q: what is difference between high voltage burn and low voltage burn explosion in details

A:

Q: What is the minimum wire size for a 30 amp circuit?

A: To determine the minimum wire size for a 30 amp circuit. For the minimum wire size refer the NEC…

Q: 31. If the voltage measuring function of a linear NTC thermistor is Vout = -1.4T( "C) + 4.35 V, the…

A:

Q: What is the difference between a current source and current sink draw diagrams aswell to explain.

A: DIFFERENCE BETWEEN A CURRENT SOURCRE AND CURRENT SINK: 1. When selecting the sort of digital input…

Q: Q: why the silicon crystal is preferred in the making of the electronic components?

A: Silicon is a semiconductor. It shows conduction property of metal at certain conditions and also can…

Q: How to get Multisim to automatically reorganize circuits?

A: Introduction Modularization and reuse are beneficial not only in software development, but also in…

Q: identify any equiptment at home that undergo an electromechanical energy conversion. name and…

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…

Q: One of the following electrical tools is used to create circuits without soldering: Circuit Board O…

A: Given :   1. Here in this question they are interested to know the electrical tool which is used for…

Q: How Pentavalent and Trivalent impurities are required to add to make the semiconductors more…

A:

Q: What is tungsten,CFL,led bulb... Which one save electricity and why ?

A: Please find your answer below.

Q: Draw the energy band diagram of the solar cell following the solar cell diagram below. Indicate the…

A: According to the question, we need to draw the energy band diagram of the solar cell shown below,

Q: All electronic components are formed from p type and n type materials. What factors determine what…

A: In p-type semiconductors, holes are the majority carriers and electrons are the minority carriers.…

Q: Draw the circuit of voltage doubler and explain its function.

A: Diode is a non linear device. Diode is used in wave shaping device. The clipper circuit is used in…

Q: Four cells each of 2.10 volt internal emf are parallel connected together to make a battery. The…

A: Each cell has emf of 2.1V and the four resistances are 0.004, 0.005, 0.003 and 0.0025. By using…

Q: 1. What is a cold solder in electronics? 2. What will happen if there is a cold solder? 3. What is…

A: Soldering is process of joining a metal parts in order to form a bond. The device used is called as…

Q: what are the five basic circuit elements?

A: The five basic circuit elements are :-

Graph theory

It is that part of network analysis where the configuration is called graph or structure of the network system when all of the elements (e.g., R, L, and C) in a network system are substituted with lines having circles/rings or dots across both endpoints. The study of the solution of the networks and circuits with the help of graphs is known as graph theory. The objective is to know the mathematics behind the network analysis.