Slide 1: In the figure below, a mass m is initially at rest. The mass is attached to a spring of constant k at via a massless stretchless string at point A, stretching the spring by Ax = 20 cm from its equilibrium length. Draw vectors representing the forces at the point A and on the mass m = 100 g. By applying Newton's Laws, solve for the spring constant k. Show your work. k A m

Slide 1: In the figure below, a mass m is initially at rest. The mass is attached to a spring of constant k at via a massless stretchless string at point A, stretching the spring by Ax = 20 cm from its equilibrium length. Draw vectors representing the forces at the point A and on the mass m = 100 g. By applying Newton's Laws, solve for the spring constant k. Show your work. k A m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A string holds and wraps around a solid cylinder (7-kg and R = 8-m). A person pulls the string vertically upward, so the cylinder's center of gravity does not move and is suspended in midair for 7 second. Note that the rotational inertia of the cylinder about its axis is MR2/2, the tension in the string is 8- N. what is the net force on the cylinder in Newton? Note: Do not include the unit in your answer. T
An object of mass m and homogeneous structure given below is in equilibrium between two springs and a damper in the vertical direction. Under the influence of the disrupting force F(t), the system is set in motion. Here, the mass of the system will be taken as m=4 (kg), k1-95800 N/m and k2= 1706 (N/m), c=704 (Ns/m). a) For the case where the input of the request is F(t) and the output is y1, find the transfer function Y1(s)/ F(s). b) Calculate the zeros and poles of the system using the transfer function you found.. m K₂ F(t) K₁ A B Y₂
A 25-kg block hangs from a spring attached to the ceiling of the elevator. If spring gets stretched by 0.15 m, find its spring constant.
or 5, 2. You have a massless spring of force constant 64 N/m, but it is wound tightly enough that you must apply 16 N of force to it before it begins to stretch. You attach a 12 kg mass to one end of the spring. The other end is fixed in place above the mass (e.g. it is clamped to the room's ceiling). A second mass of 1.0 kg is connected to the bottom of this first mass via a thin string of negligible mass. The system is initially in equilibrium, but then the string connecting the smaller mass suddenly snaps. 2.1 What is the initial acceleration of the spring-mass system? 2.2. What is the amplitude of oscillation for this system? 2.3 What would be the period of oscillation for this system? 2.4 Determine the maximum value of the kinetic energy of the mass still connected to the spring. Assume negligible damping.
The figure on the left, below, shows a non-uniform bent rod with a mass of 5 kg. Your job is to determine the location of the center of gravity of this rod. You design an experiment: you connect a pin and cable to the rod such that it safely stays in static equilibrium under a force P that you apply. Then, you apply forces between 0-100 N, and measure the tension force on the cable using a cable tension meter. The results of your experiment are shown in the figure, on the right. Using this experiment, calculate (approximately) the horizontal distance (x in the figure) between point A and the center of gravity G of the bent rod. B C O I 20 cm 20 cm 60° D 50 cm Tension measurement [N] 60 50 40 30 20 -10 0 10 real data estimated fit 20 30 40 ܐܐܝ 50 P[N] 60 70 80 90 100
A. A car's body has mass 100 slugs. This mass is supported by the car's 4 shock absorbers. The shock absorbers are identical vertical linear springs. Complete a FBD of the car's body (this would not include the car's wheels, axels etc. just the car's body) Each spring is compressed 1.25 inches. Determine the spring "k" value. Answer: 644 lb/inch. Find the compression of each spring if 4 people, each with mass 6 slugs, get into the car, Answer: 1.55" ii. iii.
R1 R2 R3 P) For the given pulleys compound system : (a) Find the Ideal Mechanical Advantage (IMA) (b) The required applied force (F) to lift 450 N load F: Applied load (c) The anchor reactions (R1, R2 and R3) (d) the movement acceleration of the load (e) Resketch the given pulleys system and label the tension force value in each part (line) of the rope. 450 N Compound Systems
For masses and are 200 kg, 300 kg, 240 kg, and 260kg respectively. The corresponding radii of rotation are 0.2m, 0.15m, 0.25m and 0.3 m respectively and the angles between successive masses are 45 , 75 and 135 . Find the position and magnitude of the balance mass required, if it’s radius of rotation is 1.4 m.
Q3: For the equilibrium position shown 4 ft 4 ft in fig. (2), 0 = 43°. Find the mass (m) of the lamp fixture suspended from the two springs, if each spring has an unstretched wwww k= 5 lb/ (before the equilibrium) length of 4 ft and k- 5 lb/t stiffness of k = 5 Ib/ft. (lamp fixture) W of lamp fixture Fig. (2)
1. The PASCO human arm model is configured such that the cord representing the bicep is perfectly vertical and the forearm is at 90° (in the figure to the right, the cord is not quite vertical). A mass of 100 g is attached to the hand. Draw a free-body diagram on the figure to the right showing all forces which act on the forearm. The force of the bicep F on the arm The force of the humerus FH on the arm The weight of the forearm W The mass in the hand Wm 100 g Be careful to draw the force vectors with tails beginning at the point where the force is actually applied to the forearm. 2. Consider the free body diagram below. Determine the perpendicular component F̟ of the force F exerted by the biceps brachii on the forearm. Use the fact that cos 0 = H/B to write this component directly in terms of the humerus length H and the biceps length B. H 3. If the forearm is in equilibrium, then there is no angular acceleration and therefore the sum of the torques applied to the forearm must be…
A rod 8 meters long and weighing 200 N is circular from the left end of the wall.It is fixed to move. The other end is connected to the same wall from above via cable.fixed. There is a 53 degree angle between the rod and the cable (Zone 2). Man weighing 800 Nstand 92 cm from the wall, the tension in the rope is the magnitude of the force the wall exerts on the rod.and find its direction. Draw the free body diagram of the system.
Three masses are attached to a 100-meter long beam as shown below. The mass of the bea, is 210 kilograms and the masses m1 and m3 are valued at 50 kilograms and 300 kilograms, respectively. Find the normal reaction force at the fulcrum that balances the system in SI units.