Sketch and explain the relationship between hydraulic conductivity and hydraulic gradient. If the gradient used in the laboratory is too high, will the measured hydraulic conductivity be higher or lower than the hydraulic conductivity expected in the field? Assume that the laboratory test is conducted on a specimen large enough to be representative of field conditions

Sketch and explain the relationship between hydraulic conductivity and hydraulic gradient. If the gradient used in the laboratory is too high, will the measured hydraulic conductivity be higher or lower than the hydraulic conductivity expected in the field? Assume that the laboratory test is conducted on a specimen large enough to be representative of field conditions

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter2: Geotechnical Properties Of Soil

Section: Chapter Questions

Problem 2.11P

See similar textbooks

Similar questions

A series of identical samples have been tested with drained triaxial test and some of the values are given in the tabulated table 3(Below). Calculate the remaining values as in the blank box. PARAMETER |cell pressure, o3 (kPa) total axial stress, 01 (kPa) pore pressure at failure, u¡ (kPa) |change in volume, Av effective cell pressure, o3' (kPa) effective total axial stress, o,' (kPa) |difference in stress, q (kPa) CD test 150 284 i 1.8 ii i iv O i = 134; ii = 16; iii = 150; iv = 0 O i = 134; ii = 284; iii = 150; iv = 0 O i = 0; ii = 16; iii = 150; iv = 134 O i = 0; ii = 150; iii = 284; iv = 134
Calculate the effective hydraulic conductivity for flow parallel and perpendicular to layering. Please show and explain the difference in values.
(a) A particular soll sample was run thru a stack a sieves and the data shown below was obtained. Find the hydraulic conductivity in (1) gpd/12 (2) m/day (b) This method of estimating K is sufficient for some purposes, but does not glve an accurate figure of the soll's true hydraulic conductivity, even when weighing errors and graphing errors are considered. 10. Why? Cumulative Cumulative weight in grams Pan # # 6 # 8 8. # 12 54 # 16 99 # 20 166 # 40 215 #70 224 Pan 238
Estimate the ratio of equivalent hydraulic conductivity
1. During Atterberg limit tests in the soil mechanics laboratory, the students obtained the following results from a clayey soil. Liquid limit tests: Number of Moisture blows, N content (%) 14 38.4 16 36.5 20 33.1 28 270 Plastic limit tests: Students conducted two trials and found that PL = 172% for the first trial and PL = 17.8% for the second trial. a. Draw the flow curve and obtain the liquid limit. b. What is the plasticity index of the soil? Use an average value of PL from the two plastic limit trails.
Q3) You are in charge of drilling operations in a sedimentary basin. The figure bellow gives the setting. Prior to drilling you have performed a numerical analysis. The table below states the necessary information at the bottom of the shale layer and at the top of the sandstone layer. Assume hydrostatic pore pressure throughout the reservoir. Stress results from your numerical models at 2250m: To [MPa] Rock layer Sy [MPa] S [MPa] S, [MPa] [deg] So [MPa] Shale Sandstone 55.2 55.2 65 40 30 20 10 0.25 30 25 30 10 5 0.25 planned wellpath Shale thickness- 2250m Sandstone: thidkness 250m A. Your drilling crew on the rig wants to drill with a setting P-Po through the shale. Will you approve this and give permission? Prove your decision by calculating the necessary stresses and show a Mohr Circle construction so that the driller can understand your reason. If unsafe, which borehole failure mechanism do we expect? ; B. Should they increase, decrease P, or stay with P=Po? Why? C. Determine the…
Name.. Q3 Water flows through the constant head setup in the laboratory, as shown in the figure, where two identical dense sand samples A and B are placed-one horizontally and the other vertically. The samples are 50 mm diameter and 100 mm in length. The water levels in the left and right sides are maintained at the levels shown, ensuring constant head throughout the test. The void ratio of the sand is 0.92 and the specific gravity of the grains is 2.69. If 165 g of water was collected in the bucket within 15 minutes, 1. What is the permeability of the soil? 2. What the pore water pressure and vertical effective stress at the mid height of sample B? OH 2 190 100+100 A = (50) 7 9 = 0.95 1963.5 100 mm crosesection מות 190 Datumn 40 mm 100 min Arey B.
A limestone core sample is saturated 100% with water. Calculate the absolute permeability of the core sample if the water is flowing at 4.15 cubic centimetres per second. The length of the core sample is 13.61 centimetres and its diameters if 7.13 centimetres. The pressure differential across the core sample is 25 atmospheric pressure and the water viscosity is 1.1 centipoises. Explain a method of how the permeability of this reservoir can be improved.
A very long steel drill pipe got stuck in hard clay at an unknown depth. The drill pipe was applied a large upward force and observed that the drill pipe came out elastically by 500 mm. It was also observed that there was elongation of 0.04 mm in a gauge length of 200 mm. Estimate the depth of hard clay bed. Following consideration may be taken into account: Resistance offered by all material/elements may be taken as zero.
Q2: The dial readings recorded during a consolidation test at a certain load increment are given below. Determine c, by both the square root of time and log of time methods. The thickness of the sample = 2 cm and the sample is drained both sides. Time Dial Reading Time min Dial Reading cm x 10-4 min cm x 10-4 0 240 15 622 0.10 318 H 30 738 C₁=0.848- 0.25 340 60 842 0.50 360 120 930 1.00 385 240 975 2.00 415 1200 1070 C,=0.197 4.00 464 8.00 530 90 H² tso
i. A sandstone core sample is saturated 100% with water. Calculate the absolute permeability of the core sample if the water is flowing at 6.21 cubic centimetres per second. The length of the core sample is 14 centimetres and its diameters is 6 centimetres. The pressure differential across the core sample is 15 atmospheric pressure and the water viscosity is 1.2 centipoises. Explain a method of how the permeability of low permeability reservoirs can be ii. improved.
For a falling head permeability test, the following values are given: Length of specimen: 200 mm Area of specimen:1000 sq. mm Area of standpipe: 40 sq. mm Head difference at t= 0: 500 mm Head difference at t= 180 sec : 300 mm Determine the hydraulic conductivity (cm/sec)