SITUATION 9: Reinforced concrete beams having width of 300 mm and overall depth of 600 mm are spaced 2.50 m on centers and support a slab of thickness 100 mm. The slab carries a superimposed dead load of 3 kPa (including floor finish, ceiling, fixtures, etc.) and live load of 4.80 kPa. The columns E and H are omitted such that the girder BEHK supports the beams DEF at E and GHI at H. Assume specific gravity of concrete is 2.40. B₁ 2.50 m El 2.50 m 2.50 m 6.00 m 6.00 m 28. Which of the following most nearly gives the factored load induced by beam DEF at E in girder BEHK? a. 354.79 kN b. 298.56 kN c. 253.87 kN d. 264.51 kN 29. Which of the following most nearly gives the factored load induced by beam GHI at H in girder BEHK? a. 354.79 kN b. 298.56 kN c. 264.51 kN d. 253.87 kN H LL F

SITUATION 9: Reinforced concrete beams having width of 300 mm and overall depth of 600 mm are spaced 2.50 m on centers and support a slab of thickness 100 mm. The slab carries a superimposed dead load of 3 kPa (including floor finish, ceiling, fixtures, etc.) and live load of 4.80 kPa. The columns E and H are omitted such that the girder BEHK supports the beams DEF at E and GHI at H. Assume specific gravity of concrete is 2.40. B₁ 2.50 m El 2.50 m 2.50 m 6.00 m 6.00 m 28. Which of the following most nearly gives the factored load induced by beam DEF at E in girder BEHK? a. 354.79 kN b. 298.56 kN c. 253.87 kN d. 264.51 kN 29. Which of the following most nearly gives the factored load induced by beam GHI at H in girder BEHK? a. 354.79 kN b. 298.56 kN c. 264.51 kN d. 253.87 kN H LL F

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum concrete and steel stresses at the point of maximum positive and negative moment. Fc'= 40 Mpa.
A 300 mm X 500 mm exterior beam is reinforced with 25 mm main bars and 12 mm stirrups. The tension side has a steel area of 2450 mm² and the compression side has a steel area of 1480 mm². 60% of the tension steel area is laid out on the first layer, the remaining is on the second layer and the compression steels are on a single layer. Determine the following if the steel yield strength of the compression steel is 276 MPa, the steel yield strength of the tension steel is 415 MPa and the depth of the tension zone 340 mm: a. The compressive stress in the concrete. b. The net tensile stress. c. Ultimate Moment Capacity of the beam.
A reinforced concrete beam is shown in the figure below. 0.75-in, diameter rods Wo 20 in. 2.5 in. 8 ft- 8 ft 10 in. Part A Determine the maximum uniform distributed load wn that can be supported by the reinforced concrete beam if the allowable tensile stress for the steel is (Ost )allow = 30 ksi and the allowable compressive stress for the concrete is (oconc )allow = 3 ksi . Assume the concrete cannot support a tensile stress. Take Est = 29(10) ksi , Econe = 3.6(103) ksi Express your answer to three significant figures.
a concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams have a span of 4.0m, web width of 259 mm and overall depth of 50 mm. the tensile reinforcement consists of 6-⌀20 mm bars in two rows with 25mm vertical clear spacing. use material strengths f'c=21MPa and fy=415MPa. calculate the ff considering a T-geometry: 1. effective flange width of an interior beam in mm 2. depth of uniform stress block at ultimate stage in mm to the nearest whole number 3. tensile steel strain compatible strain of 0.003
4.14 (B). A reinforced concrete beam of rectangular cross-section, b 200 mm, d (depth to reinforce- ment) = 300 mm, is reinforced in tension only, the steel ratio, i.e. the ratio of reinforcing steel area to concrete area (neglecting cover), being 1% The maximum allowable stresses in concrete and steel are 8 MN/m' and 135 MN/m2 respectively. The modular ratio may be taken as equal to 15. Determine the moment of resistance capable of being developed in the beam. (1.Struct.E.] [20.9 kNm.]
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
the floor framing plan of a reinforced concrete building. All beams are 300 mm x 600 mm. The properties are as follows: slab thickness = 100 mm; super imposed dead load = 3 kPa; live load = 4.8 kPa; concrete unit weight = 24 kN/m3. The columns at E and H are deleted thus girder BEHK alone supports beam DEF at E and beam GHI at H. Calculate the uniformly distributed service dead load at beam DEF in kN/m Calculate the uniformly distributed service live load at beam DEF in kN/m.
SITUATION 8: A rectangular concrete beam having a width of 300 mm is reinforced for tension only. The beam carries a factored moment of 540 kN-m. Concrete strength is f’c = 28 MPa and steel yield strength fy = 280 MPa.25. Which of the following most nearly gives the balanced steel ratio? a. 0.0349 b. 0.0439 c. 0.0394 d. 0.0493 26. Which of the following most nearly gives the minimum effective depth using a steel ratio equal to half the 582.50 sqm balanced steel ratio? a. 611.15 mm b. 675.38 mm c. 640.91 mm d. 582.50 mm27. Which of the following most nearly gives the minimum effective depth using the maximum steel ratio permitted by the code? a. 541.20 mm b. 497.21 mm c. 568.18 mm d. 518.67 mm
A concrete floor slab 100mm thick is cast monolithic with concrete beams 2.0m on centers. The beams have a span of 4.2m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameter bars in two rows with 25mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =
The steel framework shown below is used to support the reinforced concrete slab (unit weight of concrete =23.6KN/m3) that is used for an office use (minimum live load = 2.4KPa). The slab is 150 mm thick. Use a=3m, b=5m. Neglect the self-weight of the beam and girder. Assume all beams and girders have simple supports. NSCP 2015 Load factors: 1.2DL & 1.6LL. Question: True or False? The RC slab described above is ONE-WAY slab?
Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear and have a diameter of 0.250 in. Assume L= 4.0 ft. If the average shear stress in the bolts cannot exceed 70 ksi, determine the maximum distributed load wmax that can be supported by the structure. (1) A Answer: Wmax IN L B kips/ft