SITUATION 21A rectangular steel block is 300 mm in the x direction, 200 mm in the y direction and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250KN tension in x direction, 320 kN compression in the y direction, and 180 kN tension in the z direction. For Steel, Poisson's Ratios = 0.30 and E=200 GPa. 4. Determine the total strain in x direction due to the triaxial loading 5. What single uniformly distributed load in the x direction that would produce the same deformation in the x direction as the original loading.

SITUATION 21A rectangular steel block is 300 mm in the x direction, 200 mm in the y direction and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250KN tension in x direction, 320 kN compression in the y direction, and 180 kN tension in the z direction. For Steel, Poisson's Ratios = 0.30 and E=200 GPa. 4. Determine the total strain in x direction due to the triaxial loading 5. What single uniformly distributed load in the x direction that would produce the same deformation in the x direction as the original loading.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
The steel pipe shown has an outside diameter of 175 mm, a wall thickness of 18 mm, an elastic modulus of E = 200 GPa, and a coefficient of thermal expansion of ? = 11.7 x 10-6/°C. Using a = 335 mm, b = 870 mm, and ?= 60°, calculate the normal strains at Hand K after a load of P= 45 kN has been applied and the temperature of the pipe has been increased by 35°C O 16 mm, an e load of P= 45 kN has been applied and the temperature of the pipe has been increased by Answers: EH = Ek= H K με με
A steel bar 30 mm in diameter and 2 m long is encased in a shell of cast iron 5 mm thick. Compute the stress in each material, in MPa, if a compressive axial load of 150 kN is applied to the assembly. For steel, E = 200 MPa and for cast iron, E = 100 %3D GPa ( Select the correct response(s): 29.96 MPa 76.39 MPa 212.21 MPa 106.10 MPa 136.32 MPa 152.79 MPa 59.92 MPa 272.84 MPa
(1) 1d. What is the shear stress on an element with principal stresses of 565 psi and -435 psi?
Determine the normal stress and change in length of the aluminum rod if the temperature was raised by 125°C. The 0.5-mm gap exists at 20°C. q = 5 t = 0
Practice 2 A fixed ended steel beam 8m long carries a uniform load 20kN/m and an axial tensile force of 200KN. The properties of steel section is as follows: A = 7800 mm? d = 324 mm Ix = 140x10 mm ly = 16x10 mmt What is the axial stress of the beam, in MPa. What is the actual bending stress in the beam due to uniform load alone acting on the beam, in MPa. -. What is the interaction value if Fb = 210 MPa and Ft = 100 MPa? answer key а.)25.64 Мра b.) 123.43 Мра c.) 0.844
Solve please
a. At a point in a given material the three dimensional state of stress is given by ox = oy oz = 10 MPa ,Txy F 20 MPa, Tyz = %3D !! TXZ = 10 MPa. Compute the principle planes if the corresponding principles stresses are, ol = 37.3 MPa, c2 = 10MPA, o3 =2.7 MPa %3D %3D b. , What no
ASAP NEED COMPLETE SOLUTION !!
The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.
Q1