**Text:**Since the Trial 1 and 3 is a shear slump consisting height of 100-120 mm, it is considered a high workability. What are the advantages of high workability in terms of uses and such?**Table:**| Workability | Compacting Factor | Slump in mm | Use ||-------------|-------------------|--------------|-----------------------------------------|| High | 0.95 | 100-175 mm | For section with congested reinforcement |**Explanation for Educational Context:**This text discusses the concept of high workability in concrete mixtures, particularly in relation to slump tests. A slump test measures the consistency and workability of concrete. In this context, a slump height of 100-120 mm is specified as high workability, which is advantageous for sections with congested reinforcement, meaning areas where a dense network of reinforcing steel is present.The table correlates the workability level with specific measurements and uses:- **Workability:** High- **Compacting Factor:** 0.95, indicating how compact a mixture becomes.- **Slump in mm:** A range of 100-175 mm is given.- **Use:** Recommended for sections where reinforcement is dense, facilitating easier placement of concrete without segregation.

High workability, as indicated by a shear slump of 100-120 mm, offers several advantages in terms of…

Since the Trial 1 and 3 is a shear slump consisting height of 100-120 mm, it is considered a hi vorkability. What are the advantages of high workability in terms of uses and such? Workability High Compacting Factor 0.95 Slump in mm 100-175 mm use For section with congested reinforcement

Since the Trial 1 and 3 is a shear slump consisting height of 100-120 mm, it is considered a hi vorkability. What are the advantages of high workability in terms of uses and such? Workability High Compacting Factor 0.95 Slump in mm 100-175 mm use For section with congested reinforcement

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Practical Part Q4). 1- State the meaning of normal consistency of cement. 2- Which method is widely…

A: Cement A dry, powdery material known as cement is created by calcining lime and clay. It can be…

Q: • Calculate mix proportions for following conditions: Characteristic compressive strength (fc), 25…

A: 1. Find required Target mean strength : Target mean strength = Strength + Margin Strength = 25…

Q: In an unconfined compression test on a saturated clay, the maximum proving ring dial reading…

Q: Problem 3: For a sandstone reservoir, calculate the water saturation if the porosity (Ø) is (20 %),…

Q: 8. A cohesionless (c' = 0 kPa) soil specimen was subjected to a consolidated-undrained triaxial…

Q: Question 16 A direct shear test is conducted on a sand specimen. The initial cross-section area of…

Q: - In the table below, determine the elongation percent of each specimen. - Calculate the value of…

A: Step 1: To calculate elongation percentage of each specimenelongation percentage =( (final length -…

Q: A clay sample was tested in the laboratory for unconfined compressive test. Determine the undrained…

A: Given data in question Clay sample Unconfined compressive strength test was performed. Unconfined…

Q: Assume that you are going to make a three cubic yard (3 yď³) of concrete. Create your own mix design…

A: The design strength = 3.8 ksiThe slump should = 3 to 4 in.The maximum size of aggregate = 2 inUnit…

Q: Q.2. A concrete mix of (1 : 1.5 : z) by weight, The cement factor of this mix is (8 sack/1 m³), and…

Q: Indian Standard (IS) Light Compaction test is usually conducted in 3 layers in a 1000 cc mould. How…

A: Given- IS Light Compaction Test- 3 layers in 1000 cc mouldfor 2250 cc mould number of blows per…

Q: 1. For an unpaved road construction, determine the non-reinforced (without ged following…

A: Given: For an unpaved road construction, Axle Load = 80 kN Tire Pressure 480 kPa Rut Depth 0.3 m…

Q: Weight of cement Weight of Fine aggregate Weight of coarse aggregate : 17.36 kg Weight of Water :…

Q: Required maximum dry density for aggregate subbase course.

A: This result is obtained from standard proctor Test

Q: Coarse Aggregate: well-graded % in. nominal maximum-size aggregate (NMSA), crushed limestone,…

A: Given, coarse aggregate:- Oven dry specific…

Q: A good cement job is essential to allow further drilling and production operations not to proceed.…

Q: For the given w/c ratio =0.40 and mixing water content%3D190 kg/m3 determine the

Q: choose true or false 2.68, 2.72 and 2.7 is the true order of bulk specific gravity, apparent…

A: True

Q: Using the American Method, design a concrete mix for a continuous foundation with a cross section of…

A: Given:- target strength= 35MPa Dry rodded unit wt CA=1745 kg/m3 Sp. Gr. of cement =3.15 Sp. Gr. of…

Q: (m) Sketch cylindrical specimens and briefly indicate differences in applied stress states between…

A: The difference in applied stress states between CCP (AASTHO T307-99) and variable confining pressure…

Q: less clay content in aggregate lead to enhance ... ...... ....

A: Less clay content in aggregate lead to enhance the workability of concrete, performance, quality and…

Q: Explain and state visual stability index, if in slump flow test there occurs clear segregation and…

A: Solution: Visual stability method is used for determining the stability of segregation of mixture…

Q: The void ratio can never be a) Less than 1 b) Greater than 1 c) Less than zero d) Equal to 1

A: Answer : Option (c) less than zero is correct Explanation is given in next step.

Q: S The cement factor of the concrete mix is (24 sack/ 3.0 m), Find the Yield of this mix

Q: Which of the following(s) is/are the significant source of compression when loading is applied to a…

A: Which of the following(s) is/are the significant source of compression when loading is applied to a…

Q: 1- The reason of place the weights over CBR sample to ......curve 2- The relationship between…

Q: the immediate strength gained in cement soil stabilisation is due to..

A: ## immediate strength gained in cement soil stabilization is due to----

Q: 28 day compressive strength = 30N/mm2 Standard deviation = 5N/mm2 Nominal cover to steel…

A: Solution:- Given,

Q: What are the requirements of core sand?

A: Core sand is a special type of moulding sand

Q: 1.7 The compressive strength of a stone under the conditions of absolute dryness and water…

A: Solution:- Given details: Compressive strength under absolute dryness, Rdry=178 MPa Compressive…

Q: . Define yield of cement in slurry design.

A: given data : Define yield of cement in slurry design

Q: Concrete is required for a foundation located below ground where no substantial freezing and thawing…

A: Given, f'c = 4000 psi Aggregate size = 3/4 in

Q: What is the method of compaction used in bulk unit weight and voids in aggregate?

A: There are several types of method of compaction 1. Smooth wheel roller 2. Pneumatic wheel roller 3.…

Q: Given the following data: Slump Requirement 4" Max. Aggregate Size 1.0" %3D Mass of water = 193…

Q: if the % coarse aggregate 50% (Gs=2.64), % fine aggregate 43% (Gs=2.67), and % filler 7%(Gs=3.1).…

A: We will use formula of bulk specific gravity

Q: ow2 Tn a Consolidated-draned triaxial test on specimen failed at'the devialor Stress of 124 KNIm If…

Q: Concrete is required for a foundation located below ground where no substantial freezing and thawing…

A: Given:- The 28-day compressive strength (f'c) = 4000 psi The slump size = 2 in The maximum…

Q: Which state describes soil that does not show cracks when deformed (choose correct state that…

A: Liquid state is that state of soil in which soil behaves as a liquid and has negligible shear…

Q: Given the following data: Slump Requirement = 4" ements Max. Aggregate Size = 1.0" nts Water/cement…

A: Mass of cement = 350.91 kg/m3 Water/cement ratio = 0.55 Mass of coarse aggregate = 1072 kg/m3 Total…

Q: Class No= 5202 A 500 g sample of sand in the SSD condition was placed in a jar, which was then…

A: Given data- Weight of sand in SSD condition = 500 g Weight of sand and water with jar = (5202+1600)…

Q: The maximum slump height for class seal concrete is _____. a. 2 inches b. 6 inches c. 8 inches d. 4…

A: Typical slump for ordinary decorative concrete applications would be in the 4- to 5-inch range The…

Concept explainers

Properties of materials

A property of a material describes its characteristics and distinguishes it from the others. The material properties are described it in terms of its hardness, color, appearances, and so on. The material properties generally depend on the type of material, or whether it is a metal or an alloy. There are different kinds of material properties such as mechanical properties, thermal properties, physical properties, and chemical properties. Chemical properties describe the material in terms of a chemical change. The mechanical properties come into existence when the material is acted upon by an external load. Thermal properties are associated with the temperature of the material and specific heat.

Question

**Text:**

Since the Trial 1 and 3 is a shear slump consisting height of 100-120 mm, it is considered a high workability. What are the advantages of high workability in terms of uses and such?

**Table:**

| Workability | Compacting Factor | Slump in mm | Use |
|-------------|-------------------|--------------|-----------------------------------------|
| High | 0.95 | 100-175 mm | For section with congested reinforcement |

**Explanation for Educational Context:**

This text discusses the concept of high workability in concrete mixtures, particularly in relation to slump tests. A slump test measures the consistency and workability of concrete. In this context, a slump height of 100-120 mm is specified as high workability, which is advantageous for sections with congested reinforcement, meaning areas where a dense network of reinforcing steel is present.

The table correlates the workability level with specific measurements and uses:
- **Workability:** High
- **Compacting Factor:** 0.95, indicating how compact a mixture becomes.
- **Slump in mm:** A range of 100-175 mm is given.
- **Use:** Recommended for sections where reinforcement is dense, facilitating easier placement of concrete without segregation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Advantages of high workability in terms of uses and such

VIEW

Step 2: Advantages of high workability in terms of uses and such

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q Calculate the quarlity cement required in m for plaokering of mix of a wall of 5x4m with 12 mm thick plaoler 1:6.
Solve it correctly
1. ument size? yeability2 3. What factors affect porosity and permeability?
Given the following data:slump requirement = 4" max aggregate size = 1" mass pf water = .193 kg/m3 water/cement ration = .48 mass of coarse aggregates = 1105.5 kg/m3 total mass of the concrete = 2375 kg/m3 compute for the mass of fine aggregate
Problem 8.26 WD = 20 kN/m wj. = 36 kN/m 4 m concrete cover is 40 mm 6 #29 450 450 mm 70 mm 800 mm 730 mm For each of the problems, you must perform the following Recalculate the effective depth assuming concrete cover of 40 mm, and use only your calculated effective depth to answer the questions. Shear strength of concrete must be calculated using both the simplified and detailed methods of ACI318 Table 22.5.5.1. -Verity the spacing between main reinforcing bars satisfies AC1318 minimum spacing requirements. -Demonstrate the calculation of the shear forces needed to answer the questions including a fully labelled shear force diagram. The diagram must show the location within the span where 1) no shear force is required (if any), 2) minimum shear force is required (if any). Sketch (manual sketches OK) the beam and show the main reinforcement and distribution of shear reinforcement along the span, including distances where each spacing applies.
The following statements are not true about the sand replacement method except: Coarse sand is used to determine the volume of the soil The moisture content cannot be determined on site The method can be conducted for bound and unbound materials for road base The hole size prepared during the process can be varies
For most practical problems, how does the effective stress in cohesionless soil calculated/
what are the effects of the Acid Attack Test, Chloride Attack Test, and Sulphate Attack Test on the performance of geopolymer concrete based GGBS?
6. What are the properties of moulding sand?
In a consolidation test the following results have been obtained. When the load was changed from 50KPA to 100kPa, the void ratio changed from 0.70 to 0.65 a) Determine the coefficient of compressibility
The fresh mix with 5mm slump magnitude is more likely to get segregated * True False
Q26 Please provide justified answer asap