Shown in the figure below is an electrical circuit containing three resistors and two batteries. 13 www R₁ ww R3 R₂ www 1₂ • R₁ =90 • R₂ = 60 • R₂ = 10 Write down the Kirchhoff Junction equation and solve it for I, in terms of 12 and 13. Write the result here: I₁ = Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and follows the perimeter of the circuit diagram clockwise. 0 = X The resistors in the circuit have the following values: 10 Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and touches the components R₁, R₂, and 4V. 0=R₁₁+R₂1₂-4 Amperes Amperes Amperes 4 Solve for all the following (some answers may be negative): I₁ = 1₂ = | 13 = NOTE: For the equations, put in resistances and currents SYMBOLICALLY using variables like R₁,R₂,R3 and 1₁,12,13. Use numerical values of 10 and 4 for the voltages.

Shown in the figure below is an electrical circuit containing three resistors and two batteries. 13 www R₁ ww R3 R₂ www 1₂ • R₁ =90 • R₂ = 60 • R₂ = 10 Write down the Kirchhoff Junction equation and solve it for I, in terms of 12 and 13. Write the result here: I₁ = Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and follows the perimeter of the circuit diagram clockwise. 0 = X The resistors in the circuit have the following values: 10 Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and touches the components R₁, R₂, and 4V. 0=R₁₁+R₂1₂-4 Amperes Amperes Amperes 4 Solve for all the following (some answers may be negative): I₁ = 1₂ = | 13 = NOTE: For the equations, put in resistances and currents SYMBOLICALLY using variables like R₁,R₂,R3 and 1₁,12,13. Use numerical values of 10 and 4 for the voltages.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

how do i find the voltage of the capacitor? do i need to assume capacitor is charging so capacitor is open circuit and after that voltage on R2 is capacitor voltage after simplifying circuit?
1. A purely resistive circuit the current is leading by 90° with respect to voltage. 2. A purely inductive circuit the current is lag behind the voltage by 90°. 3. A purely capacitive circuit the current is lead by 90° with respect to the voltage. 4. A capacitor element stored magnetic energy. 5. An inductor element stored electrical energy. 6. Resistor elements consume power. 7. Angle between current and voltage is called power. 8. The power factor angle for a purely resistive is zero. 9. The power factor angle for a purely inductive load is -90°. 10. The power factor of a purely capacitive is leading.
A 22-k resistor and a 0.02-F capacitor are connected in series to a 5-V source. How long will it take the capacitor to charge to 3.4 V Select one: a. 0.501 ms b. 0.66 ms c. 0.44 ms d. 0.70 ms
A load is composed of a 4 ohm resistance connected in series with a 3 ohm inductive resistance. The load is connected across a 120 source. Compute: (a) current (b) voltage across the resistance (c) voltage across the inductor Explain each step.
/Q6 The potential at point P due to Q1 and * :Q2 is = 1x10-12C 0.5 m 0.5 m Q2 = 1x10-12C %3D 50 cm P. 0.01797 V O -0.01271 V O ov O 0.01271 V C 10
Figure 2 shows three "LC" circuits, two of them with capacitance capacitors "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitance capacitors "Cc". The currents that circulate through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = −dQ / dt, find the system of coupled equations of the system and then find the normal angular frequencies of the system.
Let's say you measure t1/2 to be 0.037 seconds and the resistance in the circuit is 68 Ohms. Then what is the capacitance in micro Farads? Answer in micro Farads.
Attenuators with Capacitances Construct the circuit in Figure. Use R1 = 1kohm, C1-39nF. R2=3.9kohm. Vi C1 R1 HH R2 Vo What is the effect of the capacitor C1 in the circuit? You may use equations to help explain your answer.
An inductor and a resistor are in series with a sinewave voltage source. The frequency is set so that the inductive reactance is equal to the resistance. If the frequency is increased, then options: Voltage across the inductor= Source Voltage Voltage across the inductor> Voltage across the resistor Voltage across the inductor= Voltage across the resistor Voltage across the resistor > Voltage across the inductor
3-10 A0.25-F capacitor has a current waveform i(t) as shown in Figure P3–10. Determine and plot the voltage waveform v(t) as a function of time. The capacitor is initially a and plot the voltage waveform v(t) as a function of time. The capacitor is imu uncharged. FIGURE P3-10 ilt) 4 A 6. -4 A
Using the series circuit in Figure 3 consisting of a voltage source V, the resistor R and the fully uncharged capacitor C, how to find the value of the capacitance C considering as known data the time constant of the circuit T and the value of the resistor R? V ww R
The picture shows three LC circuits, two of them with capacitors of capacitance C and the three with coils of inductance L, the three circuits are coupled by means of two capacitors Cc capacitors.L inductance coils, the three circuits are coupled by means of two capacitors of capacitance Cc. The currentscirculating through each mesh are those indicated in the figure: I1, I2 and I3. Using Kirchhoff's law for voltagesand taking into account the definition of current I = -dQ/dt, find the system of coupled equations for the systemand then find the angular normal frequencies of the system.