Show that, when steady state is reached, the temperature T, atthe interface of a composite slab, consisting of two differentmaterials with R values R, and R,, is:RTh +R2T.TxR +R2where T, is the temperature on the outer surface of the first slab(R value R,) and T, is the temperature on the outer surface ofthe other slab (R value R).

Answered: Image /qna-images/answer/7dfdffea-3602-4a52-9fff-57b475e5d765.jpg

Show that, when steady state is reached, the temperature Tx the interface of a composite slab, consisting of two different materials with R values R, and R,, is: at RTh + R2T. Tx R +R2 foog of the first slah

Show that, when steady state is reached, the temperature Tx the interface of a composite slab, consisting of two different materials with R values R, and R,, is: at RTh + R2T. Tx R +R2 foog of the first slah

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

2 inch outer diameter throughout a plastic sheet milla 60 m long section of a horizontal steam pipefrom one end to the other, on which it passes without comparisonis observed. Ambient air and surface temperaturesAt 20 ° C, several hours measurements are the average of the exposed surfaces of the steam pipe.shows that its temperature is 160 ° C. The outer surface of the pipe appears to be oxidized andemissivity can be taken as 0.6. According to this;a) Calculate the heat loss in the steam pipe.b) Some steam is produced in a gas oven operating at 60% efficiency. Factory 105,500kJ natural gas pays $ 1.10. If it is assumed that the factory operates all year (365 days), for this facilitycalculating the annual cost of heat losses in the steam pipe.
The isotermal bulk modulus is defined as
The amount of thermal expansion coefficient (a) if the length of a copper rod is (5 m) at a temperature (20) and at a temperature (60), the length of the wire will increase to (Ans = (5.0036 m d = 18x10 deg / %3D
What is the average translational kinetic energy of molecules in an ideal gas at 50 °C?
Nuclear fusion, the energy source at the Sun, hydrogen bombs, and fusion reactors, occurs much more readily when the average kinetic energy of me alums is high-that is, at high temperatures. Suppose you want me atoms in your fusion experiment to have average kinetic energies of 6.40 × 10-14J. What temperature is needed?
When a metal is heated, its atoms vibrate more about their position in the lattice (a network of crossed bars). This causes them to take up more space, so the solid metal expands from its original shape. Calculate the heat needed to expand a ring made of copper with an internal diameter of 50mm to fit over a shaft of diameter 50.05mm. The shaft is measured at a temperature 20 degrees c
Expert Q&A Done A copper slug whose mass is 125g is heated to a temperature of 350°C. The slug is dropped into a 600 g glass beaker with 400 g of water. The initital temperature of the water and beaker is 15°C. Assume the system is located and no vaporization occurs. Find the equilibrium temperature of the system.
Ur an exposed wheel diameter of 30.000 cm at a temperature of 15 C and the internal diameter of the iron rim of 29.930 cm. So to what temperature must the rim be heated in order for it to slide on the wheel? For this type of iron ('a = 1.10x10 c) %3D
You are studying a liquid that you have just synthesized in the laboratory, and you would like to get a rough idea of its enthalpy of J -), you measure its normal boiling point and find that it is mol. K vaporization. Assuming that it reflects Trouton's rule (namely that A vap 368 K. Use this result to estimate AvapH in kJ/mol. S≈ 88-