SHOW COMPLETE SOLUTION & ILLUSTRATIONA 100m tape weighing 3kg was standardized and found to be 0.02m short at a temperature of 10°C and a 30N pull when supported throughout. It was used to measure a distance which was recorded as 3245.68m when the temperature was 15°C and a pull of 40N supported only at quarter points. If E =200Gpa and the density of the material is 7500kg/cu.m. Coefficient of thermal expansion is 11.6x10^-6/°C. Find the correct distance between the two points. A 100m tape weighing 3kg was standardized and found to be 0.02m short at a temperature of 10°C and a 30N pull whensupported throughout. It was used to measure a distance which was recorded as 3245.68m when the temperature was15°C and a pull of 40N supported only at quarter points. If E =200Gpa and the density of the material is 7500kg/cu.m.Coefficient of thermal expansion is 11.6x106/°C. Find the correct distance between the two points.

Actual length = l' = 100m Measured length = L = 3245.68m E =200Gpa Coefficient of thermal expansion…

SHOW COMPLETE SOLUTION & ILLUSTRATION A 100m tape weighing 3kg was standardized and found to be 0.02m short at a temperature of 10°C and a 30N pull when supported throughout. It was used to measure a distance which was recorded as 3245.68m when the temperature was 15°C and a pull of 40N supported only at quarter points. If E =200Gpa and the density of the material is 7500kg/cu.m. Coefficient of thermal expansion is 11.6x10^-6/°C. Find the correct distance between the two points.

SHOW COMPLETE SOLUTION & ILLUSTRATION A 100m tape weighing 3kg was standardized and found to be 0.02m short at a temperature of 10°C and a 30N pull when supported throughout. It was used to measure a distance which was recorded as 3245.68m when the temperature was 15°C and a pull of 40N supported only at quarter points. If E =200Gpa and the density of the material is 7500kg/cu.m. Coefficient of thermal expansion is 11.6x10^-6/°C. Find the correct distance between the two points.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

can you help me with detailed solution pls 2. A line was measured with a steel tape which was exactly 30m at 18°C and a pull of 50N and the measured length was 459.242m. Temperature during the measurement was 28°C and the pull applied was 10ON. The tape was uniformly supported during the measurement. Find the true length of the line f the cross sectional area of the tape was 0.02cm², the coefficient of expansion per °C = 0.0000117 and the modulus of elasticity = 21 x 10° N per cm².
NOTE: The standard pull of the tape is 5kg while the team pulled only at 4kg The field temperature is 300 while the standard temp of the tape is 200 The cross sectional area of the tape is 0.05cm2. The coefficient of linear expansion is 0.000011610C and the modulus of elasticity of steel is given to be 2.0 x 106 kg/cm. The tape used here is a 50m steel tape. Determine the actual length of each lines
Please provide correct solution
A beam shown below, 200mm wide by 350mm deep, is loaded as shown in figure below. Determine the stress in a fiber 50mm from the top of the beam at point B. 50kN A 20 купи RI B 2M X 30KN/M TITT. 4m 20 km. ITTJ 2m + <
Determine the horizontaldeflection of B.
Situation 8: The rigid, horizontal slab is attached to two identical copper rods. There is agap A = 0.08 mm between the middle bar, which is made of aluminum, and the slab.Neglecting the mass of the slab, the temperature in in all rods by 60°C. Use the following data: Each bronze rod Aluminum rod 22. Compute the stress in bronze rod 23. Compute the stress in aluminum rod 24. Compute the deflection on the rods Bronze A (mm²) 650 480 A Aluminum a (/°C) 18.9 x 10-6 23.1 x 10-6 Bronze 850 mm E (GPa) 83 70
Engr. Sova Ho used 30m length of tape in measuring a distance line. The measured length of the line was recorded to be 454.62 m. During the measurement the temperature reading was 11 oC and the tape was supported at both ends. The cross sectional area of the tape is 6.50mm2 and the modulus of elasticity is 200 GPa. The tape has a weight of 0.075 kg/m. K= 11.6 x10-6 m/c. If the engineer determined the Temperature correction, Pull correction, and Sag Correction lengths to be 1,640.01 μm, 588μm, and 1.71 mm respectively, per segment. Calculate the applied Pull of the 30m tape in kg.
A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears at a stress of 310 MPa, determine the minimum force P required to punch the slot. Punch 705 kN 660 kN 844 KN 904 kN O 772 KN Slug Plate 20 mm 75 mm Plan view of slug Que Nume Blank Que Nume Blank Que Nume Blank Que Nume Blank Que Nume Blank View Que Multi Que Multip Que
A line was found out to be 2865.35 m long when measured with a 30-m tape under a steady pull of 6.5 kg at a mean temperature of 30 degC. Determine the correct length of the line if the tape used is of standard length at 20 degC under a pull of 5.5 kg. Assume that the cross-sectional area of the tape is 0.025 cm², elastic modulus of tape is 2.10 x 106 kg/cm? and coefficient of linear expansion of steel is 11.6 x 106 per degC.
The stress–strain diagram for the material of a column can be approximated as shown. Plot P/A vs. KL/r for the column.