A motor driving a solid circular steelshaft transmit 40kw of power at500rpm. If the diameter of the shaft is40mm. Then determine the max.Shear stress in the shaft.

Given data; A motor driving a solid circular; steel shaft transmit =40 KW of powerSpeed , N=500…

Answered: Shear stress in the shaft.

Engineering

Mechanical Engineering

Shear stress in the shaft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: what is the value of maximum principal stress in the figure below?

A: Find the maximum principal stress .

Q: d Given: 9/8 in 2 in Diameter of bolt = 7/8 inch Diameter at the root of the thread (bolt) = 0.731…

Q: What would be the recommend torque and max torque for a hollow shaft made of 52100 bearing steel…

A: Let's first determine the recommended torque for the hollow shaft using some math. Step 1: Torque is…

Q: On principal plane shear stress is _________ Select one: a. Optimum b. Minimum c. Maximum d. Zero

A: The shear stress is zero on a principal plane.

Q: the bending endurance limit for AISI 1080 steel shaft is Select one: a. 307.5 MPa. O b. 250 Mpa c.…

Q: What happens when a shaft having a circular cross-section is subjected to a torque?

A: When the torque is subjected to the shaft, the shear stress is generated in the shaft, and this…

Q: A 3/8-inch diameter bolt is subjected to a 2,135-lb tensile load. The bolt passes through a very…

Q: Please use maximum shear stress theory

Q: "Design a shaft face journal bearing for a fixed radial load of 1500 lb, while the shaft rotates at…

A: Given Load = 1500lb N = 850 rpm ==85060=14.166 rev/s D = 2.1 in To find Design of journal In this…

Q: Write the formula used to determine the average shear stress?

A: shear stress is the stress produced due to shear force.

Q: --------stresses are induced in the shafts if the shafts are manufactures by cold drawing process.

A: Drawing is a process in which a metal is stretched through a die using tensile forces.

Q: a, = 200 Mpa 3D o, = 450 Mpa Tay = 200 Mpa Click here to see all formulas Part A - Determine the…

Q: without it! Q.5) The shaft shown below has a 1.5-inch diameter solid Steel (G= 11,200 ksi) segment…

A: Given:d=1.5 inG=11200 ksi for steel G=6400 ksi for brassTorque=60 lb-ftTo find:The maximum shear…

Q: In one revolution of a shaft the stresses which vary from a value of tensile stress to the same…

A: cyclic stress occurred when load carrying element is subjected to some value of tensile stress to…

Q: 5) Normal stresses includes stresses due to axial load, bending moment and torque. A- True B-False

A: Normal stress occurs when stress is induced in perpendicular direction of cross section of…

Q: d Given: 9/8 in Diameter of bolt = 7/8 inch V2 in Diameter at the root of the thread (bolt) = 0.731…

Q: Can the segments of the shaft be subjected to different internal torques?

A: The internal torque on a shaft can be varied according to the cross-sectional area. The torque can…

Q: 2. The composite shaft of total length 1.8 m consists of 5 mm thick brass and is fixed to a 30 mm…

Q: The thread depth is measured along the ----------------- of the thread. Pitch Crest Angles Face

A: Thread: A thread is a simple machine structure mainly used to convert the the linear motion of force…

Q: The principal stresses are given as 20, 0 and 30 respectively, what is the shear stress? Selected…

A: To find: The shear stress. Given: The principle stress is σ1=20, σ2=0 and σ3=30. Concept used: The…

Q: Homework: Draw shearing stress distribution of the critical section? 500kN H 12mm 150mm 12mm 276mm…

Q: How can we determine the maximum shear stress in the shaft?

A: Torsional shear stress is the stress set up a member when it is subjected to two equal and opposite…

Q: A straight line joining the endurance limit on the Y axis to the yield stress on the X axis is…

Q: A machine part is subjected to an axial loading situation where Fmin = 3700 lbf and Fmax = 12000…

A: Given:Maximum axial force, Fmax=12000 lbfMinimum axial force, Fmin=3700 lbfCross-sectional area,…

Q: Handwritten solution required!! Do not type

A: Step 1: Convert the rpm to radians per second by using the formula w=2π×n/60 where n is the speed in…

Q: Another very common mode of failure of gear teeth is that due to surface damage or pitting, which…

A: Given: The causes, and some of the measures that can be taken to prevent failure of gear teeth due…

Q: What are the three most critical materials properties linked to the functional demands of materials…

A: Given:Options are given with properties:

Q: Why is the allowable shear stress checked?

A: Stress which is induced in a material due to the tangential forces, is termed as shear stress. This…

Q: How is the shear center determined?

A: Shear Center The shear center is a point on the section of the beam, from where the resultant load…

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

Q: The shear stress at the inner surface of hollow circular section is __

A: The shear stress at the outer surface of the hollow circular section is maximum and minimum at the…

Q: How is the angle of twist of a circular shaft determined?

A: Angle of twist When the torsional load is applied on the free end of the shaft, then the fixed end…

Q: Describe Bending Stress

A: Bending stress is the normal stress that an object encounters when it is subjected to a large load…

Q: Illustrate the given term with the help of neat Principal plan Torsional shearing stress Mohar…

A: Principal plan When a material undergo biaxial or triaxial state of stress then the stresses induce…

Q: The design of a machine element calls for a 40-mm-outer-diameter shaft to transmit 41 kW. If the…

A: Outer diameter= 40mm Power Transmission= 41 kW Rotation= 730 RPM

Q: Where is the maximum stress depending on ?the distance from the neutral axis إجابتك

A: Maximum stress is on the outer most layer of beam .In figure below, upper most layer has maximum…

Q: For the shallow shaft, the inside diameter, d is generally expressed in terms of the outside…

A: Given data, Shallow shaft D = Outside diameter. d = Inside diameter. Find Relation between d &…

Q: Define the term wide-flange sections?

A: Wide flange section Wide flange sections are those sections in which the flange of the section is…

Q: Ixoxd 150 pints a and b of the cantilever shafts show in the figure 10 KN 2. 200

A: Given: Transverse load on the beam: →P=10 KN=10000 N Length of the shaft→L=200 mm=0.2 m Outer…

Q: Given: Diameter of bolt = 7/8 inch Diameter at the root of the thread (bolt) = 0.731 inch Inside…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

100%

A motor driving a solid circular steel
shaft transmit 40kw of power at
500rpm. If the diameter of the shaft is
40mm. Then determine the max.
Shear stress in the shaft.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

• Compute the maximum shear stress and angle of twist of each type of shaft below. – Closed tube shaft – Open tube shaft • Briefly describe which type of shaft is more effective. • See the dimensions of each tube, the value of internal torque, and the shear modulus in the next page.
5) Normal stresses includes stresses due to axial load, bending moment and torque. A- True B-False die
3. 15/16-inch-wide key has a depth of 5/8 in. It is 12 inches long and is to be used on a 200 hp, 1160 RPM, squirrel cage induction motor. The shaft diameter is 3 7/8 inches. The maximum direct shearing stress on the key, considering the effect of the keyway.
HW12 The gearing of a machine tool is shown in the Figure below. The motor shaft is connected to gear A and rotates at 1500 r.p.m. The gear wheels B, C, D and E are fixed to parallel shafts rotating together. The final gear F is fixed on the output shaft. Fined: 1-the speed of gear F 2- rotating speed of gears (B, C, D and E) The number of teeth on each gear are as given below: Gear A B C D E F No. of teeth 25 35 90 30 80 60 + A B E+ D F LL
The shaft whose torque varies from 3000 to 7000 in-lbs has 1.5 inches in diameter and 65,000 psi yield strength. Compute for the shaft mean average stress. d.6,036 psi c.11,909 psi b.8,904 psi a.10,377 psi
compute the compressive stress
Can the shafts be subjected to cyclic or fatigue stress?
True or false ? State if it’s true or false
draw the assembly in cross-section.
The customised shaft has a diameter of 50 mm. A square parallel key is suggested to be used for mounting a gear into this shaft. The shaft is to be made of SAE 1095 Carbon Steel with a yield stress of 572 MPa. The gear is made from SAE 1045 Carbon Steel with a yield stress of 531 MPa. A key can be made of SAE 1018 Carbon Steel with a yield stress of 372 MPa or SAE 316 Stainless Steel of 241 MPa. The gear transmits torque of 2,000 +P N-m and has a hub length of 100 mm. The design factor is chosen as 3.0 and the width of the key is 12.7 mm. Specify the keys using two materials and explain which material should be recommended in such a design scenario. Key Figure 1: Key, Gear and Shaft You may use the following equations: == T D/2(WL) 4T σ DLH 2T L = TDW 4T L= σDH
S2 - 9 and 10
20. A pin is used to join the two members shown. If the allowable average shearing stress in the pin is 190 MPa, what is the minimum required diameter for the pin? a. 8mm b. 3/8 inch 25 kN 12 mm C. 10 mm d. 1/2 inch 7.5 mm 12 mm 7.5 mm 25 kN 18. The motion of the follower of a cam-follower system is governed by x = R(1+1/2 coscot). If R = 70 mm and (= 62.8 rad/min, determine the magnitude of the acceleration of the follower, in mm/s², when t = 0.8 s. a. 18 c. 22 d. 24 b. 20