Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress concentrations associated with the sudden change in cross-section. Determine: (a) The maximum shear stress in the shaft (b) The rotation of the end E relative to the end A. 500 N-m 300 N-m A 30 mm) B 400 mm C 150 N-m 300 mm 350 mm D 50 N-m 2020 E 450 mm 20 mm

Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress concentrations associated with the sudden change in cross-section. Determine: (a) The maximum shear stress in the shaft (b) The rotation of the end E relative to the end A. 500 N-m 300 N-m A 30 mm) B 400 mm C 150 N-m 300 mm 350 mm D 50 N-m 2020 E 450 mm 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Don't Copy please.
The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine load P that can be applied at C if the stress in the steel rod is limited to 120MPA. E=200 x 10° N/m2 A-300mm? L-3m 3 m 4.5 m
2)For the supporting frame shown below: a) Determine the internal forces acting at section a-a. b) Determine the stress components that act at points A and B. IN = 2.6525x10-7 mª -300 mm 150 mm 2.5 kN a 12 mm 6 mm 6 mm 6 mm 36 mm'36 mm Section a – a
44 ksi 3 ksi 70 S ksi Given the state of stress above (ignore 70° plane): calculate the maximum shear stress, maximum principal stress and minimum principal stress in this order. Choose only one answer.
الامتحان اليومي الثاني )ميكانيك المواد I I( Q: For the state of stress shown in fig. below. Determine the principle stress and the max. shearing stress .show all results on complete sketches of differential element. 30 MPa 60 MPa -60 MPa 40 MPa 40 MPa 30 MPa
Q-5: For the element with stresses as shown below, find: a. The magnitudes and directions of major and minor principal stresses b. The shear and normal stresses acting on a horizontal plane as shown below 8kPa 2kPa 75° 75° экра TH Jon OH 4kPa 30° Horizontal plane
please answer all parts step by step and clear answer.
Please answer correctly, badly need it. Thank u godbless The internal shear force at a certain section of a steel beam is V= 8.8 kN. The beam cross-section shown in the figure has dimensions of b=141 mm, c=31 mm, d=63 mm, and t=6 mm. Determine: (a) the shear stress at point H. (b) the shear stress at point K. (c) the maximum horizontal shear stress in the cross-section. Break the cross-section into five rectangles, as shown. It is seen that the two labeled with a (1) are identical, and the two labeled with a (2) are identical. Find A1, the area of rectangles (1), and y1, the vertical distance from the bottom edge of the cross-section to the centroid of rectangles (1). Similarly, find A2, the area of rectangles (2), and y2, the vertical distance from the bottom edge of the cross-section to the centroid of rectangles (2). Then, find A3 and y3 for rectangle (3). A1= mm2 y1= mm A2= mm2 y2= mm A3= mm2 y3= mm Find y¯, the vertical…
c2
Reg.no : 5395 MOS-2
QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is applied to the end B of the shaft. Determine the rotation of section B. The shaft and beam are made of an aluminium alloy for which E= 720 GPa and G = 27 GPa, Neglect the strain energy of the hub DF. IC 400 mm 200 mm- 40.0 mm D 60.0 mm 400 mm 800 mm HO H 30.0 mm T= 2.00 kN.m
1.) Draw the internal stress and strain diagram of beam considering that the depth of the stress block is greater than the thickness of the flange. f’c =30 MPa, fy=400 MPa and is subjected to a positive bending Mu=140KN-m.