Answered: Select the reinforcing needed for the…

Select the reinforcing needed for the short tied column shown for the following: Pn-2200 kN, e= 250 mm, e, 120 mm. f 28 MPa, fy- 420 MPa: (Add attachments below) Note: Check with Bresler equation

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Compute its design strength based on rupture in kiloNewtons..* 412 485 453 389 438 This is a…

A: Given, Fu = 400 MPa Fy = 248 MPa D = 16 mm Dh = D + 2

Q: q) what is the tensile rupture capacity of flange plate of the flange connection in kips? (2 decimal…

A: Yield Strength : Yield strength is a maximum stress a structure can bear beyond the maximum stress…

Q: Check the bolted section of the given gusset plate connection assuming that the connection is done…

Q: O Which of the following gives the max. shearing stress if P = 40 kN, e = 45", a = 300 mm, b- 450…

Q: The connection of the drawbar and tie plate combination given below will be made by welding with two…

A: Welded connections: The point at which two or more pieces of metal are joined together is known as…

Q: The wall bracket show below carries a load of P Kip. the allowable tensile in the eye bar is 20 ksi,…

A: According to question :

Q: A riveted connection is shown in the figure 3.26. A 25 mm diameter A 502, grade 2 rivets are used. A…

A: To compute:Tensile strength when shear stress of rivet governsTensile strength when bearing stress…

Q: A flanged bolt coupling consists of 6 - 12 mm - diameter bolts on a bolt circle of 320 mm i…

A: Given data in question Shearing stress Torque Diameter To find out Additional number of bolts…

Q: REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P= 50…

Q: 35nun 15mm B Pu 200mm

A: According to given data Answer- 5 4-22 mm diameter bolts are used in a staggered bolted To,…

Q: 0: The bracket shown carries an eccentric load P at an eccentricity e = 400 mm. the column and…

A: Given data:(a) Polar Moment of inertia

Q: The details of an end bearing stiffener are shown in Figure . The stiffener plates are 9⁄16-inch…

A: A572 Grade 50:Fy=50 ksi Calculating the bearing strength: Apb=6-0.5×916×4=12.38 in2Rn=1.8 Fy Apb…

Q: 1-66 Figure P1-69 shows a bolt subjected to a tensile load. One failure mode would be, if the…

Q: Describe how transportation influenced the initial settlement and subsequent development of your…

A: Transportation plays a very crucial role in the initial settlement and development of society. It…

Q: Determine the allowable tensile force P which can be appllied to the plates shown. The AISC…

A: Diameter of bolt, Thickness of plate, Width of plate, To find: Allowable tensile force.

Q: 5. what is the shear rupture capacity of the shear plate of the shear connection in kips? (2 decimal…

A: a)Thickness of shear plate= 0.5 inA992: Fy = 50 ksi, Fu = 65 ksiA36: Fy = 36 ksi, Fu = 58…

Q: Determine the maximum factored LRFD tensile force capacity in tension only (no block shear). The…

A: We know that Maximum factored LRFD tensile force capacity of the member is given by minimum of the…

Q: How many (answer should be a whole number) 22-mm diameter rivets are required to fasten member BC to…

Q: Bolted and Riveted Connections 1. From the bolted connection shown, the diameter of bolts is 18mm0…

A: Solution: Given: db = 18 mm dbo = 18+3 = 21 mm Section: 100 x 75 x 8 mm Ag = 1340 mm2 t = 9 mm A36…

Q: PROBLEM 1: CHECK THE ADEQUACY OF MEMBER BC WHOSE THICKNESS IS 14 mm, FIGURE : to

Q: what should be the mini mum For the tigure s how n, dia meter OF the rivets attached as shown TF the…

A: given data allowable axial stress =60MPa allowable shearing stress = 110 MPa width of plate,b =100…

Q: Calculate the strass In each mamber and identify what the factor of safely to failure 13? 19

A: Given:- Cross section of the members is 3" x 10" To find:- Stress in each members Concept:- Method…

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: Answer We know that LRFD capacity of the connection is given by minimum of the below three capacity…

Q: The single angle 102 x 203 x 13 is connected on the long leg by two 20 mm diameter bolts as shown in…

Q: Design a welded connection for an MC9x23.9 of A572 Grade 50 steel connected to a 3/8-inch-thick…

A: A572 grade 50 steel connected to 3/8 inch thick gusset plateThe gusset plate is A36 steelTo…

Q: REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P =…

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: Answer In order to calculate the minimum acceptable tensile service load we need to first find the…

Q: miscellaneous channel MC 300 x 67 is bolted as shown on the figure 2.20 by a 0 mm diam. bolts. A 36…

A: Area of section, Depth, Thickness of web, Flange thickness, Width of flange, To find: (a)…

Q: what is the flexural rupture capacity of the shear plate of the shear connection in kips?

A: A36: Fy = 36 ksi, Fu = 58 ksieffective bolt hole diameter = bolt hole diameter + 1/16"bolt diameter…

Q: what is the tensile rupture capacity of flange plate of the flange connection in kips? (2 decimal…

A: Given that :-properties of beam are - Properties of material are -Required that :- tensile rupture…

Q: The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for…

A: Area = Force/ Shear stress

Q: Answer fast and send right answer

Q: The five-bolt connection must support an applied load of P = 3900 lb. If the average shear stress in…

A: Given data in question Load 3900 lbShear stress 35 ksi5 boltsTo find out Diameter of bolt

Q: For the connection shown, determine : a) Sigma (stress) on the plate, if N = -6 kN (negative sign…

A: Given:- Thickness of plate, t = 10 mm Width of plate, w = 2R = 2 x 30 = 60 mm Diameter of pin, d =…

Q: cd efgh O ij klmn u op V q 0 k i What is the line for which the section will rupture in tension? All…

Q: The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58…

Q: limited to 48 ksi, determine the minimum bolt diameter that may be used for this connection. (coc00…

A: To find the minimum diameter of bolt (dmin.)-

Q: 1. Two A36 16mm thick steel plates are connected by four rivets shown. 50 PU O 50 x 50 50 a.…

Q: For the beam shown find the value of Force (F) Ib and maximum stress due to flexure (Ob b ) psi if…

A: Given:- The shear force in the bolts = 300 lb The shear stress in beam = 120 psi The spacing between…

Q: QUESTION 4 – Single Angle Tension Member - Bolted The single angle 102 x 203 x 13 is connected on…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

Select the reinforcing needed for the short tied column shown for the following: Pn-2200 kN, e
250 mm, e, 120 mm. f 28 MPa, fy- 420 MPa: (Add attachments below) Note: Check with Brester
equation
70mm
500 mm
640 mm
70mm
70 mm
70 mm
210 mm
350 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. what is the bolt shear capacity of the shear connection in kips? (2 decimal places)A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips
Please solve with complete detailed solution. Thank you.
20. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksit) what is the weld capacity perpedicular to the beam of the flange connection in kips? (2 decimal places)
From the bolted connection shown, the diameter of bolts is 20 mm with the hole diameter equal to 3mm larger than the bolt diameter, the angular section is 100x75x8mm, with an area of 1340 mm^2. Thickness of gusset plate is 9 mm. the gusset plate. (a)If T = 200KN, compute the shearing stress on the bolts. (b)If the allowable shearing stress on the bolt is 145MPa, compute the value of T.
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
Please help with the problem below
16) what is the tensile yielding capacity of flange plate of the flange connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
A staggered connection is shown in the figure. Using LRFD & ASD, determine the maximum tensile force that the plate could carry. Assume A36 steel (Fy = 248 MPa, Fu = 400OMPA). Use NSCP 2015 provisions. For Plate: t = 12 mm, width = 350 mm For Rivet: Diameter = 20 mm 70 100 70 80 70
2. The figure shown is bolted with a diameter of 22mm. The inner plate material is 12mm x 315mm and the outer plate material is 9mm x 315mm. Assume hole diameter is 2mm larger than the bolt. T/2 T/2 F, = 345MPA, F, = 450MPA, F, = 207MPA, F, 1.2F, for bearing type connection. F, a friction type connection. = 117MPA for 45mm 75mm T/2 a. Determine the tensile capacity of the plates if it is a bearing type connection. b. Determine the tensile capacity of the plates if it is a friction type connection. c. Compute the minimum theoretical length of the lap if it is a bearing type connection. 75mm T/2 75mm 45mm A в А
Five M20 8.8/ bolts are used in the connection between a beam and a column. Both sides of the cleat plate are welded to column using fillet weld (Manual metal arc AS4855 B-E43XX) with size of 5 mm. The design force transferred from beam to column is 300 kN. The cleat plate has thickness of 12 mm, fy = 300 MPa, and fü = 360 MPa. Determine the unit stress sustained by the weld