Select the correct choice.1, In the actual cycle, the effect of variation in specific heats in is to(A) Increase maximum pressure and maximum temperature(B) Reduce maximum pressure and maximum temperature(C) Increase maximum pressure and decrease maximum temperature(D) Decrease maximum pressure and increase maximum temperature2. In a petrol engine, the mixture has the lowest pressure at the(A) Beginning of suction stroke(C) End of compression stroke(B) End of suction stroke(D) None of these3. In a high speed engine, 4-stroke cycle the inlet valve(A) Opens at top dead center and closes at bottom dead center(B) Opens at 10° before top dead center and closes at 60° after the bottom dead center(C) Opens at 10° after top dead center and closes 20° before the bottom dead center(D) May open or close anywhere

Since you have asked multiple questions in a single request, we would be answering only the first…

Select the correct choice. 1. In the actual cycle, the effect of variation in specific heats in is to (A) Increase maximum pressure and maximum temperature (B) Reduce maximum pressure and maximum temperature (C) Increase maximum pressure and decrease maximum temperature (D) Decrease maximum pressure and increase maximum temperature

Select the correct choice. 1. In the actual cycle, the effect of variation in specific heats in is to (A) Increase maximum pressure and maximum temperature (B) Reduce maximum pressure and maximum temperature (C) Increase maximum pressure and decrease maximum temperature (D) Decrease maximum pressure and increase maximum temperature

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

T B A D Consider the cycle in the diagram (very similar to the Rankine Cycle) using water as the working fluid. Process A-B: A saturated mixture of water is pumped from low pressure to a high pressure saturated liquid in an iso-entropic (and adiabatic) process. Process B-C: The high pressure saturated liquid enters a boiler where it is heated at constant pressure process by an external heat source to a super-heated vapor. Process C-D: The super-heated vapor goes through a turbine, generating power exiting as a saturated vapor. Assume an iso-entropic (and adiabatic) process and neglect kinetic energy and potential energy changes. Process D-A: The saturated vapor then enters a condenser where it is condensed at a constant pressure process back to its original state. The boiler operates at 10 MPa (points B & C) and the condenser operates at 100 kPa (points A & D). Assume a mass flow rate of 1 kg/s. a) Make a table of the temperature, pressure, volume, internal energy, enthalpy, entropy…
c. A thermodynamic cycle in which air is the working fluid, has the following reversible non-flow processes: 1st process (1-2): The air is compressed adiabatically through a volume ratio of 6:1, the initial pressure and temperature being 103 kN/m? and 100°C respectively. 2nd process (2-3): The air is heated at constant volume until the pressure is 3,450 kN/m?. 3rd process (3-4): The air is expanded adiabatically to its original volume. 4th process (4-1): The air is cooled at constant volume to its original state. For air, R = 0.287 kJ/kgK, and y=1.4. i. Calculate the missing values of the pressure, volume and temperature for each of the state points 1,2,3,4. ii. Determine the amount of heat transferred to the air between state points 2 and 3. ii. Sketch the thermodynamic cycle on a P-v diagram and T-s diagram.
A regenerative steam cycle renders A. increased work output per unit mass of steam В. decreased work output per unit mass of steam C. increased thermal efficiency decreased work output per unit mass of steam as D. well as increased thermal efficiency
B- A steam generation unit in power plant operates at a constant pressure of (10 bar) and the water evaporates at the rate of (0.9 from the total mass flow rate of water). Inlet and leaving water enthalpy are (200 kJ/kg) and (2000 kJ/kg) respectively. The inlet and outlet velocity are (10 m/s) and (25 m/s) respectively. If 80% of the heat energy supplied to the steam generation unit is used in evaporating the fluid. Determine the heat evaporation and work done if the inlet and outlet diameter are the same level. The fuel produces 28000 kJ of heat energy for one kg and the mass flow rate of water is 1000 kg/h.
Determine the efficiency of a constant volume cycle withlexpansion ratio equal to 7.8. **Express final answer in TWO DECIMAL PLACES Do not round off in between solution. Type only the "numerical value". No need to include the unit and percent sign. Answer:
What are the practical limitations to maximum work being able to be done from an engine when all the processes ard reversible.
Can you briefly define the Stirling cycle and write down its biggest message?
Please explain each step
Isentropic efficiency of a turbine. If the process between the inlet state and the exit pressure.
T B A D Consider the cycle in the diagram (very similar to the Rankine Cycle) using water as the working fluid. Process A-B: A saturated mixture of water is pumped from low pressure to a high pressure saturated liquid in an iso- entropic (and adiabatic) process. Process B-C: The high pressure saturated liquid enters a boiler where it is heated at constant pressure process by an external heat source to a super-heated vapor. Process C-D: The super-heated vapor goes through a turbine, generating power exiting as a saturated vapor. Assume an iso-entropic (and adiabatic) process and neglect kinetic energy and potential energy changes. Process D-A: The saturated vapor then enters a condenser where it is condensed at a constant pressure process back to its original state. The boiler operates at 8 MPa (points B & C) and the condenser operates at 200 kPa (points A & D). Assume a mass flow rate of 1 kg/s. Make a table of the temperature, pressure, volume, internal energy, enthalpy, entropy and…
Problem: The drawing (not to scale) shows the way in which the pressure and volume change for an ideal gas that is used as the working substance in a Carnot engine. The gas begins at point A (pressure = PA, volume = VA) and expands isothermally at temperature T until point B (pressure = PB, volume = V B) is reached. During this expansion, the input heat of magnitude Qn enters the gas from the hot reservoir of the engine. Then, from point B to point C (pressure Pc. volume = Vc), the gas expands adiabatically. Next, the gas is compressed isothermally at temperature T. from point C to point D (pressure = PD, volume = VD). During this compression, heat of magnitude Q. is rejected to the cold reservoir of the engine. Finally, the gas is compressed adiabatically from point D to point A, where the gas is back in its initial state. The overall process A to B to C to D to A is called a Carnot cycle. Prove The work done during the cycle equals the area enclosed by the path on the PV diagram. B…
A heat engine has to exchange heat with -----thermal reservoir at --- different temperatures to produce work in a complete cycle. Select one: O a. one, two O b. two, two O c. two, one O d. one, one