Select any diode from LTSpice Library. (The type of diode should either be RECTIFIER or SILICON)Create a Half-Wave Rectifier circuit.Use a resistor of 1000 Ohms.Input Voltage should be 95VAC - 65HzPlot both the Input voltage and output voltage.Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks.Create a Bridge-Type Full Wave Rectifier Circuit.Repeat the steps done on the Half-Wave Rectifier circuit. I. General Instruction• Select any diode from LTSpice Library. (The type of diode should either be RECTIFIER or SILICON, See Fig.1)V Select DiodeOKCancelPart No.Mfg.typeVbrkdn[V] Iave[A] SPICE ModelRR264M-400RohmRectifier400.00.70.model RR264M-400 D(Is=5!RR264MM-400RohmRectifier400.00.70.model RR264MM-400 D(Is=RRE07VS4SRohmRectifier400.00.70.model RRE07VS4S D(Is=6iRRE07VTM4SRohmRectifier400.00.70.model RRE07VTM4S D(Is=RRE07VTM6SRohmRectifier600.00.70model RRE07VTM6S D(Is=RRIVWM4SRohmRectifier400.01.00.model RR1VWM4S D(Is=5.1SR154-400RohmRectifier500.01.00.model 1SR154-400 D(Is=53>· FIGURE 1• Create a Half-Wave Rectifier circuit.• Use a resistor of 1000 Ohms.• Input Voltage should be 85VAC - 50HZ, if the last number of your student number is ODD.• Input Voltage should be 95VAC - 65Hz, if the last number of your student number is EVEN.• Plot both the Input voltage and output voltage.• Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks.• Create a Bridge-Type Full Wave Rectifier Circuit.• Repeat the steps done on the Half-Wave Rectifier circuit.See Sample FA2-P2 uploaded on our GDrive HALF-WAVE RECTIFII.Open with Google Docsa. Circuit SchematicPLACE CIRCUIT HEREFigure I: Half-Wave rectifier Circuitb. Half-Wave Signal12v-10VVino120v--20V47V120V100m

Answered: Image /qna-images/answer/fa638abb-e1b8-4b75-8d30-811e907ae293.jpg

Select any diode from LTSpice Library. (The type of diode should either be RECTIFIER or SILICON) Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 65Hz Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.

Select any diode from LTSpice Library. (The type of diode should either be RECTIFIER or SILICON) Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 65Hz Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
What is the difference between a diode and rectifier?
The reverse recovery time of diode is trr = 3 s and the rate off all of the diode current is di/dt = 30 A/s. The storage charge current QRR is?
In the circuit shown below, find the diode voltage VD and the supply voltage V such that thecurrent is ID = 0.6mA. Assume the diode threshold voltage is 0.3 V. Determine the powerdissipated in the diode
Draw the following rectifier circuits with an input voltage of 12 Vrms and an RL=2K. Determine the output voltage and the current in RL. Plot these waveforms indicating the peak values and the time as per calculation. Also solve for the output DC value. Use silicon diode/s in your analysis. Half wave rectifier circuit (include the diode voltage analysis), Full wave bridge rectifier circuit, Full wave rectifier using center tapped transformer
• A Si diode at a temperature of 25°C has VD = 0.7V at Is = 10nA. The temperature is raised to 125°C. 1. Calculate ID at 25°C. 2. What is effect of rise in temperature on VD & IS 3. Calculate ID at 125°C.
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
Draw a full wave bridge rectifier circuit with input voltage is vz = 18 sin(1100t), design the filter circuit for 0.25 V ripple voltage. Assume that the load resistance of the circuit is RL = 500 N and the each diode parameters are V, = 0.7 V and rf = 0 N %3D respectively.
In RL load connected (without free transition diode), single phase, uncontrolled, full wave rectifier (4 diodes), the source voltage is sinusoidal and its effective value is 44Volt, 50 Hz. The ohmic load value connected to the circuit is 10 ohms. Average value of load current calculate. (L>>R) a) 4.16 A b) 3.46 A C) 3.26A d) 4.56 A e) 3.96 A
5) The figure below illustrates a simple voltage threshold detection circuit. To understand how it operates, we will analyze its behavior based on the simple constant voltage drop model for both diodes. Assume the Zener diode (Z1) only conducts when its breakdown voltage of 10V is reached. Di is a red light emitting diode (LED). Assume it conducts after its forward bias voltage of 1.8V is reached. Vin is unknown. Assume Zj acts as a perfect Zener diode (without series resistance). What voltage does Vin have to reach before there is a current through R¡? What voltage must Vin reach before current flows through R2? Write an equation for the current through Zi in terms of Vin, Rị and R2 that is valid when Vin is high enough for both diodes to be conducting. a. b. c. R2 Vino R1 LED
2. What are the main differences among Generic Diode, Zener Diode, Schottky Diode and Trans-Vers diode (TVS diode )? please provide an original response, thank you