See image attached Example #:An 80% efficient, series wound domotor has an armature resistanceof0.020hmsandafieldresistance of 2000hms. Themotor suppliesdrawing an unknown current at440V. Determine:800Wwhenа.The power drawn by themotorb. The back emf

Answered: Image /qna-images/answer/a87253ce-e534-4aed-86c6-afb5ac8ff714.jpg

Answered: See image attached

Engineering

Electrical Engineering

See image attached

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

help me in these questions pls write the questions with the and by (Computer) 1-Which of the following statements INCORRECTLY explain the label in the figure about LVDT working principles? a. Secondary coils are connected in series in such a way that their output is opposing each other. b. Constant DC voltage input to primary coil. c. Displacement moves ferrous rod from central position. d. The difference of the output voltage between the two secondary voltage.==========2- Explain the working principle of the measurement system in the figure below.i. Force input that is supplied to the sensor is processed to give the response in the form of raw output signal.ii. Signal conditioner manipulated the weak signal to give a conditioned input.iii. Analog or digital indicator display the unit that gives output reading of quantity being measured.iv. Measured value is compared with the input value for further action. a. ii, iii and iv only. b. i, ii and iv only. c. i, ii and…
Draw dc load line :
Get the electromechanical analog model (torque-voltage or torque-current) of the system. With all the steps of the analysis
Explain the concept of power quality in electrical systems and the potential issues that can arise, such as voltage sags, harmonics, and flicker.
4. Explain the relationship between back emf E, terminal voltage V and coil voltage drop IR in DC motor and generator respectively. i. Describe how the field strength affect the performance of DC motor and generator. ii. Explain how an external resister changes the DC motor and generator performance.
the armature mmf can be -2 reduced by reluctance of the magnetic the circuit in the region of the pole .tip a) Increasing, O b) decreasing O c) don't put O
A step up chopper has an input of 200 volts and output of 250 volts. The blocking period is each cycle is 0.6x10-3 seconds. Find the period of conduction in each cycle and frequency of operation?
If the ratio of V/F has been kept constant and the observed value of hysteresis loss at rated frequency of 50 Hz is 18 W, the measured value of core losses is 35 W, Find the total core losses at the frequency of 60 Hz.
Maz a) A sinewave is having a frequency of 50 Hz and instantaneous value of 250 Volts at 1.3 milli seconds. Find D The maximum value of sinusoidal voltage waveform and i) The value of voltage at 2.1 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and 0 =40 degrees. on Vp Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximnum value = a) (ii) Value of voltage at 2.1 ms = b) Angular frequency =
A 20 kVA machine has a full load copper loss of 400 W, an iron loss of 150 W, and a mechanical loss of 200 W. Determine:a) Efficiency at 3/4 of full load with f.d.p. 0.8. Ans: 95,43%b) Performance at full load with f.d.p. 0.9. Ans: 96%c) Peak performance apparent power. Ans: 18,71 kVAd) Yield in the previous case for f.d.p. Unit. Ans: 96,39% I need the procedures to get these results. Thanks
A 120V dc motor draws 200A is located 1000’ from the supply line. The diameter of the wire is 0.45” ; the specific resistance is 10.4 ohm – CM / ft. What is the supply voltage? *
Untitled Section Jalis 6 In d.c. generators armature reaction is produced by field current O armature current commutating winding current none of the mentioned compensating winding current *.The use of d.c. generators eliminated the use of rectifiers and ac supplies True False O