Saturated air at 40°F (4.4°C) is first preheated and then saturated adiabatically. This saturated air is then heated to a final condition of 105°F (40.6°C) and 28% rh. To what tem- perature must the air initially be heated in the preheat coil? [Ans: 101°F (37.8°C)] please solve without psychometric chart

Saturated air at 40°F (4.4°C) is first preheated and then saturated adiabatically. This saturated air is then heated to a final condition of 105°F (40.6°C) and 28% rh. To what tem- perature must the air initially be heated in the preheat coil? [Ans: 101°F (37.8°C)] please solve without psychometric chart

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter28: Special Refrigeration Applications

Section: Chapter Questions

Problem 2RQ

See similar textbooks

Similar questions

Choose the correct result for the following نقطة واحدة The value of dryness fraction at -1 critical point for water-steam phase „transformation may be 1 All of these Either 0 or 1 نقطة واحدة During the dryness fraction measurement using throttling calorimeter the wet state of steam is throttled so as to lie in Superheated state None of these Subcooled state Wet state
VAPOR COMPRESSION REFRIGERATION SYSTEM ANALYSIS 3 Warm environment Он Condenser Expansion valve Evaporator QL Cold refrigerated space in Compressor 1 FIGURE 1: VAPOR COMPRESSION REFRIGERATION CYCLE The chiller system operates based on the vapour compression refrigeration cycle (figure 1) with a single stage compression. The isentropic efficiency of the compressor is assumed at 85%. The refrigerant exit evaporator and condenser can be assumed as saturated.
11.4 If 42.0 kJ of heat is added to a 32.0-g sample of liquid methane under 1 atm of pressure at a temperature of – 170°C, what are the final state and temperature of the methane once the system equilibrates? Assume no heat is lost to the surroundings. The normal boiling point of methane is –161.5°C. The specific heats of liquid and gaseous methane are 3.48 and 2.22 J/g-K, respectively [find more in Section 11.4]. P = 1.00 atm 42.0 kJ 32.0 g CH4 AHvap = 8.20 kJ/mol T = -170 °C
1. Determine the phase(s) present for each of the following working fluids and conditions. If a two- phase mixture is present, determine the quality of the system. a. Water, T = 45°C , P = 5.848 MPa b. Ammonia, h = 778.52 kJ/kg, T = 0°C c. R22, P = 80 Ibf/in?, v = 0.9318 ft2/lbm d. Water, T = 395°F, v = 1.337 ft/lbm e. R134a, T = -15°C, P = 0.8 bar
Completely solve and provide the diagram. Box the final answer. Write legibly 4. A single effect water evaporator operating at 125 kPa abs vapor pressure. Motive steam is available for evaporation at 1.0 MPa with 90% vapor content, what is the mean temperature difference?
Define a near-azeotropic refrigerant blend, and give twoexamples.
Instruction: Show all your solution and Use the steam table, attached: https://drive.google.com/file/d/1I3WGlSBL7MbPkhEfJumTc2vCjvLfyXB6/view?usp=drivesdk A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar and 530°C. The two reheater pressures are 10 bar and 0.6 bar, and the steam leaves each reheater at 480°C. Condensation occurs at 0.03 bar. What is the steam flow rate in kg/s for an engine output of 20,000 kW?
what are the instruments/materials used by scientist to study Thermoclines under water.
What is the name of the heat transfer occurring at D in the following heating curve for water? Sensible Fusion Evaporative Capacitive Latent
1. Sketch a diagram for the experimental instrumentation and devices.2. State any possible error source in the experiment.3. State any suggestions to improve the experiment or find new way to estimate the latent heat offusion.4. Compare the exact value with that obtained experimentally and estimate the error percentage.5. There are three important latent heats, what are they?6. What is mean by the critical point and what is mean by triple point for pure substance?7. How does the pressure affect the value of latent heat of fusion?
Identify the amount of enthalpy needed in order to turn steam into 450g h20 (water) that is located at a temperature of 85 degrees Fahrenheit ANS: _____ British Thermal Unit
Question: 3 Calculate the dryness fraction, specific volume and internal energy ‘u’ of steam at 7 bar and specific enthalpy =2600 kJ/kg