Safe stress for the steel bar shown in the figure is sigma(safe)= 160 MPa. According to The greatest shear stress (Tresca) and Von Mises hypotheses a)By neglecting the cutting effect b)Taking shear effect into account Check whether this rod bears the given load.

Q: According to a stiffness based design, a solid shaft has a diameter 50mm and the shear modulus of…

A: here, G= 35 Gpa = 35000 Mpa d = 50mm J = pi×d^4/32 mm4 Torsional rigidity = G×J.

Q: Problem 2 Determine the total elongation of the bar shown in figure below. Materials E (GPa) Bronze…

A: Answer: The total elongation of the bar : ∆Ltotal = ( -7.517 × 10-5 × P ) mm  where, P is in…

Q: Kesis Kesit A r2 Secb o KesitB 80 M. |00

A:

Q: From the figure below, a shaft consists of different sections. Bar (a) is a hollow bar and has an…

A:

Q: The maximum shear load (Vmax) – positive (+) value if upward, negative (-) value if downward • The…

A:

Q: Using the maximum-shear-stress (MSS) theory determine the factor of safety for a bar of AISI 1020…

A: Q) Given data         σx = 170 MPa        σy = 90 MPafor AISI 1020  carbon steel σyt = 350 MPaTo…

Q: the height (in mm) of cross section from strength calculation           h = ?

A: working stress = yeild stress/ factor of safety = 220/1.6 = 137.5 MPa

Q: Example 1 A high strength steel band saw, 20 mm wide by 0.80 mm thick, runs over pulleys 600 mm in…

A: Given data: The width of band is w=20 mm The thickness of band is t=0.8 mm The diameter of pulley is…

Q: Example 1.6 Around bar as shown in Fig-1- is subjected to an axial tensile load Of 100KN . what must…

A:

Q: D = 1.300 in, d = 1.000 in, h = 0.125 in, and r = 0.125 in. The member is made of steel with Sut =…

A:

Q: 2. A solid steel rod with a diameter of d = 50mm is subjected to a bending moment M = 1.5 kN-m and a…

A:

Q: 1. As a section cut in a prismatic bar varies from 0 = 0° to 180° at what values of 0 will the…

A: To find:

Q: Soderberg relation in your design. Also calculate the mean stress in N/mm2.

A: For solution refer below images.

Q: When a bar with the hexagonal cross section shown in Fig. (a) is subjected to a torque T, numerical…

A:

Q: Given the shear modulus(G) for aluminum as 2.4e+10 N/m2 and the shear strain is given as 6e-5. What…

A: From hook's law  Shear stress is directly proportional to shear strain within elastic limit

Q: please very urgent In the bar in the figure, on the joints A and CCalculate the reactions. (Bending…

A: Drawing the free body diagram of the given beam, Hence the horizontal reaction at C is P.   To…

Q: Two strip of metal are pinned to gather as shown in fig below with a rod of 10 mm diameter. The…

A: Given Information: The diameter of the rod (d) = 10 mm The ultimate shear stress of the rod (S) = 60…

Q: An aluminum rod is rigidly attached Regd: Pmax between a steel rod and a bronze rod as shown in Fig.…

A:

Q: digit of your ID No., mm) and 10 mm thick (plus quarter of the last digit of your ID No., mm). It…

A:

Q: To use the torsion formula to relate the torque applied to a rod of circular cross section to the…

A:

Q: A compound bar consisting of bronze, aluminium and steel segments is loaded axially as shown in…

A:

Q: Find the smallest diameter for the one bolt that can be used in the figure if P = 90 kN. The working…

A: The given figure shows a single riveted joint with double plate  To find :  the area of the bolt…

Q: e 3 m high is fixed at the base. It is 6mm thick and its outside diameter is 300mm. The pole is…

A: Given:h=3 mt=6 mmD=300 mmT=25 kN.mF=3 kNG=78 GPaζallow=60 MPa

Q: A tensile load of 6 kN at 25 C was applied to a steel rod stretching between two rigid walls as…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: 28. A prismatic bar PQRST is subjected to axial loads as shown in the figure. The segments having…

A:

Q: Example 3.3: A double riveted double butt joint in plates 20 mm thick Cover is made with 25 mm…

A:

Q: H.W.6: A hollow circular cold-rolled bronze [G, = 6,500 ksi] tube (1) with an outside diameter of…

A: Given that, Modulus of rigidity of bronze tube 1, Gt=6500 ksi,Outside diameter of tube 1, do=1.75…

Q: The figure shows a bar with a point load of 22 kN applied at the free end, the other end of the bar…

A: Given data: F=22 kNd=6 mm Need to determine the shear stress in the bolt.

Q: 1.5 Figure 1.9 shows a circular steel rod of length 40 m and diameter 8 mm, which hangs in a mine…

A:

Q: A solid round bar. 25 mm in diameter. has a groove 2.5-mm deep with a 2.5-mm radius machined into it…

A:

Q: Torsional T is applied to the hollow axis (G=80 GPa). Ewha Womans University, the maximum shear…

A:

Q: A steel bar withstands simultaneously a 30 kN compressive force, a 5 kNm bending moment and a 1kNm…

A:

Q: Question: Consider that the fit between the elements shown in the Figure below is H6/s5. They are…

A: given data

Q: Write down the compatibility equation.  e. Determine the average normal stress in the aluminum and…

A:

Q: The figure below shows a stepped shaft having D = 35 mm, d = 25 mm, and r= 3 mm. The shaft is made…

A: Given Data: The ultimate tensile strength of the shaft is, σut=450 MPa. The corrected fatigue…

Q: H.W.6: A hollow circular cold-rolled bronze [G, 6,500 ksi] tube (1) with an outside diameter of 1.75…

A: solved

Q: Example 9.3. A double riveted double cover butt joint in plates 20 mm thick is made with 25 mm…

A:

Q: Determine the pin dieameter at A if the allowble s

A:

Q: A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric…

A: Draw a diagram showing the centroidal axis and neutral axis in the cross-section. Here, CA is the…

Q: n Figure 1, with its dimensions, loading status and material properties, different full circle…

A: Given data

Q: A cantilever beam, 80 mm wide by 230 mm high and 8 m long, carries a load that varies uniformly from…

A: Type of beam: Cantilever beam Width of the beam, b= 80 mm Height of the beam, h= 230 mm Length of…

Q: For a steel beam loading, the maximum normal compressive stress is - 6 MPa, maximum normal tensile…

A:

Q: A bar is subjected to fluctuating tensile load from 20kN to 100KN. The material has yield strength…

A: As per given question  Fluctuation tensile load P1=20kn…

Q: When a steel rod below is subjected to torque (T = 1 kN · m) and bending moment (M = 4 kN m)…

A: Given data: The magnitude of torque is T = 1 kN.m. The magnitude of the bending moment is M = 4…

Q: A steel pipe is part of a drilling rig to build foundation piles The outer d 2 is equal to 6 in and…

A: To obtain the magnitude of the shear force on the various fibers of the beam, we must use the pure…

Q: rods as shown in the figure below. Rod A has a diameter of 12 mm and manufactured from steel with…

A:

Q: A cantilever beam, 80 mm wide by 220 mm high and 8 m long, carries a load that varies uniformly from…

A: Find the normal stress in a fiber 70 mm from the top of the beam at a section 5 m from the free end.

Q: The beam shown in the figure is made of steel with oal=300 MPa. Determine the maximum load, P, that…

A: According to the given information, we have a beam which is shown in the figure, the stress in steel…