FProblem 6/80/9 The light bar is used to support the 50-kg block inits vertical guides. If the coefficient of static fric-tion is 0.30 at the upper end of the bar and 0.40 atthe lower end of the bar, find the friction force act-ing at each end for x = 75 mm. Also find the maxi-mum value of x for which the bar will not slip.50 kgВProblem 6/96/10 The semicircular 5-kg plate rotates about a fixedbearing at O that can exert a maximum frictionalmoment of 1.2 N.m on the plate. The horizontalforce P is applied to a cord wrapped around the plate300 mm

Answered: Image /qna-images/answer/8be08ba9-ef1c-4e79-8ecc-406b992e0ca2.jpg

S79 The light bar is used to support the 50-kg block in its vertical guides. If the coefficient of static fric- tion is 0.30 at the upper end of the bar and 0.40 at the lower end of the bar, find the friction force act- ing at each end for x = mum value of x for which the bar will not slip. 75 mm. Also find the maxi- 50 kg A 300 mm

S79 The light bar is used to support the 50-kg block in its vertical guides. If the coefficient of static fric- tion is 0.30 at the upper end of the bar and 0.40 at the lower end of the bar, find the friction force act- ing at each end for x = mum value of x for which the bar will not slip. 75 mm. Also find the maxi- 50 kg A 300 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

7. (c) A load P of 5000 Kg on the crank pin of the crank shaft as shown in figure is required to turn the shaft at constant speed. The crank shaft is made of ductile steel having yield strength of 2800 Kg/cm2 as determined in simple tensile test. Calculate the diameter of the shaft based on a factor of safety of 2.5. Use maximum shear stress theory. Consider section m-n as critical section. 'm 20cm P 15cm
Calculate the ultimate moment capacity of the special beam as shown. Assume fc'=21Mpa and fy=415Mpa. 200mm 80 mm 400mm VA 4-32mm 400mm Calculate the depth of compression block 100mm 200mm 200 mm _mm
wrong answer gets downvote so double check the answer cause it will be input in the system
An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The minimum force P required to prevent rotation of the flywheel is applied. Please show complete solution.
A horizontal beam ABC is loaded as shown in the figure below. The distance of the point of contraflexure from end A (in m) is 10kN (327) Ag 0.75m B C k D 1m -
1
Q6b .solve this.
3/99 SS The uniform 15-kg plate is welded to the ver- tical shaft, which is supported by bearings A and B. Cal- culate the magnitude of the force supported by bearing B during application of the 120-N-m couple to the shaft. The cable from C to D prevents the plate and shaft from turning, and the weight of the assembly is carried en- tirely by bearing A. 200 mm 120 N·m A B 200 mm PROBLEM 3/99 80 mm 600 mm D 400 mm
A cantilever beam shown in Fig, with rectangular section shown. Its carry uniform load wand concentrated load Pa=12 KN, F-0.5. a- Calculate the instantaneous and 6- years long-term deflections at free end b - Check the deflections with ACI-Code limitations. Pa 012 stirrups 66 29 2 29 K-bw fy bw, L W, kN/m? h, mm Wa mm 27 410 180 3.25 4.75 5.6 500
If the clamping force at G is 900 N, determine the horizontal force F that must be applied perpendicular to the handle of the lever at E. The mean diameter and lead of both single square-threaded screws at C and D are 25 mm and 5 mm, respectively. The coefficient of static friction is μ = 0.3. Answer: F = 66.7N 200 mm- -200 mm OA C 125 mm
J- A distributed load op w (kulm) is applied over the entire tength OF a simply supported beam Gm long . The beam section is as shown. Determine the maximum value OF w iF Of Ś 1OMP , and yE 800KP. 80 mm X 200 mm 360mm 200mm
724A mechanism carries a constant load P applied to the seat as shown. For the angle 0, determine the following 400 E (a) the lengths LBE and LAB, in m (b) the angles a and 9, in degrees Draw the complete FBD of (c)members AB, FG, EBH and GHI Calculate the forces, in Newtons, for the following (d) member FG (e) pin H (f) hydraulic cylinder AB 100 175 LBE op os ude a This is not yoproperty so do not upon any way aswer your own 150 D E 150 C 175 B 34.5 degrees 200 Dimensions in millimeters G H P = 724 N 150 This is not your property so do not use it in any way as if it were your