Answered: S. A rectangular beam 10 cm wide, is…

S. A rectangular beam 10 cm wide, is subjected to a maximum shear force of 50,000 N, the corresponding maximum shear stress being 3 N/mm2. The depth of the beam is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Prob. 1.4-13. For the overhanging beam shown in Fig. P1.4-13, determine: (a) expressions for the int...

Q: A 3.5˚ curve is to be designed on a highway with a design speed of 60 mi/h. Spiral transition curves...

A: Given, Degree of curve, D=3.5°Design speed, S=60mi/hrAngle of deflection, ∆=40°P.I station=15100+26t...

Q: Consider two RCC beams, P and Q each having the section 400 mm x 750 mm (effective depth, d = 750 mm...

Q: Problem 3 The tube shown below has a uniform wall thickness of 12 mm. For the loading given, determi...

Q: A steel tape with a unit weight of 76.5 kN/m³ and having a cross-sectional area of 2 mm? is used to ...

A: L=85.95m Po =5.44kg A=2.5mm2 =0.025cm2

Q: Determine which of the lines shown below are parallel to each other.

A: If 2 lines seem parallel to 2 ADJACENT views, we will able to conclude that these lines are parallel...

Q: 30 kN 50 kN to B D A 1m 3 m 2 m Figure P-403

Q: A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areident...

A: Given:- L = 1.0 m, A = 3000mm2, modulus of elasticity E = 45 GPa, gap s = 1.0 mm. To find:- (a) Ca...

Q: Problem 2 Two 10-kN forces are applied to a 20 x 60-mm rectangular bar as shown. Determine the stres...

A: We have to determine the value of the stress at point A when (a) b=0, (b) b 10 mm, (c) b=25 mm asper...

Q: d 1.59 m d = 5.22 feet Problem 8-12 0-mm-diameter concrete pipe is laid on a slope of 1 m per 500 m ...

A: To Determine From where sinθ is taken from, in the solution given.

Q: The upper shell is believed to be formed from.. up to a depth of 1000 km ..... granite clay sand O

A: We have to determine that is upper shell is believed to be formed from which of the granite, clay, s...

Q: Eenerate the stiffness matrix for the frame corresponding to three degrees of freedom 1, 2. 3 A 3 B/...

Q: Prob. 1.4-4. For the pin-jointed truss in Fig. P1.4-4, (a) deter mine the reactions at the supports ...

A: To find support reaction and force in members AB,BC,CD

Q: Given figure shows a portal frame with loads. All members of frame have same plastic moment of resis...

Q: A steel column carries moment Mx = 11kN.m and My = 16.5 kN.m and an axial load of 220 KN. The steel ...

A: A steel column carries moment Mx = 11kN.m and My = 16.5 kN.m and an axial load of 220 KN.The steel s...

Q: 12. Jet propulsion of ship is less efficient than screw propeller due to

A: To find: Why is jet propulsion ship less effective than screw propeller .

Q: Draw the FDBS of member ADB and BEC 1 m 1m B |C E 1 m 1.6 m A

Q: The L-shaped arm ABCD shown in the figurelies in a vertical plane and pivots about a horizontalpin a...

A: Given:- L-shaped arm ABCD To find:- (a) Obtain a formula for the elongation of the spring due to th...

Q: Consider two RCC beams, P and Q each having the section 400 mm x 750 mm (effective depth, d 750 mm) ...

Q: 2. Draw the FBD of the entire structure C 18 kN 2 m В 2 m E 2 m A -3.6 m-

Q: A foundation is to be constructed for a small residential building that is approximately 6.0 metres ...

Q: 10. Given the diagrams in Figure P5.1 of progress on individual work pack- ages of a project, answer...

A: Given Data : BCWS = budget cost of work scheduled (planned value) ACWP = Actual Cost of Work Perfor...

Q: Problem 1 A bar obtained by bonding together pieces of aluminum (E, = 70 GPa) and brass (E, = 105 GP...

A: We have to determine the value of largest moment M that can be applied about the horizontal axis acc...

Q: Whenever the particle more rounded the porosity increase True False O

A: Porosity is defined as volume of void to volume of total soil. due to rounded shape void will increa...

Q: PROBLEM 2) The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 8) Determine lo...

Q: The width and effective depth of a reinforced concrete beam is 250 mm and 440 mm respectively. The b...

Q: A body having mass 4 Kg, viscous damping coefficient is 20 N-s/m and the spring constant is 16 N/m. ...

A: This question is related to Vibration from Solid Mechanics.

Q: The working stresses are 120 MPa in tension and 90 MPa in compression. Determine the smallest safe c...

Q: OF HYDRAULIC CEMENT BY VICAT NEEDLE give example with solution ( i need example of this) interpolat...

A: data given Time Vs penetration data is give Initial setting time 33-35mm penetration At final set...

Q: Gabbro is found in the oceanic crust and is distinguished by its black or dark .. * .color

A: Introduction: This question comes from geotechnical and geology engineering. Gabbro is a coarse-gra...

Q: Exa A rectangular sedimentation tank following coagulation- flocculation is to treat a flow of 3000 ...

Q: The gross command area of an irrigation project is 1 lakh hectares. The culturable command area is 7...

Q: Analyse the box-frame by moment distribution method. Plot bending moment diagram. 1.5 m P 20 kN +H E...

Q: Reservoir B Z8 = 9 m

Q: 5. If exactly 20 bolts of 2.5cm diameter are needed to hold an air chamber together at A-A as a resu...

Q: 10mm 203mm 10mm BI 15 KN/M To D L/3 L/3 L/3 14mm 10000mm 94.5mm. 94.5m Girder ABCD Cross Section 274...

Q: 8oklm Given data . 土A TRA 个Rc 2m 不

Q: . Calculate the annual cost of slaked lime and soda for treating Ea 70,000 litres of water per day, ...

Q: Use virtual work method and determine the following unknowns on the frame shown below. Use I = 800 ...

Q: 2) What is the deformation 8gc in mm?

Q: y = 248 MPa Area = 21300 Ix = 300000000 Iy = 98800000 Sx = 2080000 Sy = 746000 d = 289 tw = 19.2 tf=...

Q: Consider two RCC beams, P and Q each having the section 400 mm x 750 mm (effective depth, d 750 mm) ...

Q: A reinforced concrete beam of rectangular cross-section of breadth 230 mm and effective depth 400 mm...

Q: 67. In case of damaged prestressed concrete I girders which are used for restoring strength? A. O Pr...

A: Option B is correct

Q: 8. If the pressure remains a constant, then a) Vr1 > Vr2 b) Vr1 < Vr2 c) Vr1 = Vr2 d) Vr1 is a zero

Q: 67. In case of damaged prestressed concrete I girders which are used for restoring strength? A. O Pr...

Q: The cross section includes the following features: Discuss each feature of the cross section. a. Tr...

Q: H.W The uniform thin pole has a weight of 50 N and a length of 26m. If it is placed against the roug...

A: The given figure is shown below:

Q: The given section of the beam is at acting at the point of maximum moment of the beam loaded shown. ...

Q: 7. If the friction is neglected, then, a) Vr1 > Vr2 b) V.a < \V.a

A: To find: What happens when friction is neglected

Concept explainers

Solid Mechanics

Engineering mechanics is a branch of science that deals with forces causing bulk motion in bodies and the effect that these forces cause on the bodies. Engineering mechanics does not deal with the internal changes that occur on account of these external forces. The internal effects in a body or a material under the action of external forces are studied in a new branch of science called solid mechanics, the strength of materials, or the mechanical behavior of engineering materials.

Question

S. A rectangular beam 10 cm wide, is subjected to
a maximum shear force of 50,000 N. the
corresponding maximum shear stress being
3 N/mm2. The depth of the beam is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

-2.4m- 8 mm 200 mq 8 mm 250 mm 8mm The steel beam has the cross-sectional area shown. The beam is loaded as shown with the intensity of the distributed loading w=70 kN/m. Determine the absolute maximum bending stress in the beam in MPa.
If the wide-flange beam is subjected to a shear of V = 30 kN, determine the maximum shear stress in the beam. 200 mm a. 4.62 MPa b. 4.48 MPa с. 1.65 МРа d. 1.99 MPa e. None of the above 30 mm 25 mm B 250 mm 30 mm 200 mm
Determine the maximum shear stress in the T-beam at section C. 150 mm 10 kN/m 150 mm|30 mm E30 mm 3 m +1.5 m--1.5 m-
Determine the maximum shear stress in the T-beam at point C. 150 mm 10 kN/m T 150 mm 30 mm |C --30 mm 5m +₁. 3 m- -1.5 m-1.5 m- A B
F1-7. The uniform beam is supported by two rods AB and CD that have cross-sectional areas of 10 mm² and 15 mm², respectively. Determine the intensity w of the distributed load so that the average normal stress in each rod does not exceed 300 kPa. B 6 m W C
Q2/ The overhang beam is subjected to the uniform distributed load having an intensity of w = 30 kN.m. Determine:- 1- Draw Shear force and bending moment diagrams of the beam. 2- The absolute maximum bending stress developed in the beam. 3- Draw the distribution of bending stress over the cross section at the location of the maximum shear stress. B -3 m - 3 m - 50 mm 100 mm
If the beam is subjected to a shear force of V=40kN, a. Compute the maximum shear stress b. Compute the shear stress 10mm below the uppermost part of the cross section of the beam.
Problem 3: Determine the maximum shear stress in the T-beam at section C. 150 mm 10 kN/m 150 mm 30 mm tismfis -30 mm E +1.5 m→–1.5 m-| - 3 m-
0.2: Consider the cantilever beam subjected to the concentrated load shown below The cross section of the beam is of T-shape. Determine The shearing stress 20 mm from the top surface of the beam of a section adjacent to the supporting wall. 50 KN 120mm 2 т 20mm 120mm 20mm
P1 Determine the maximum shear stress in the T-beam at section C. Show the result on a volume element at this point. 10 kN/m 3 m- -1.5 m--1.5 m- 150 mm 150'mm 30 mm |30 mm
11-95. The beam has the rectangular cross section shown. If w = 1 kN/m, determine the maximum bending stress in the beam. Sketch the stress distribution acting over the cross section. %3D 50 mm I 150 mm -2 m- -2 m- -2 m Probs. 11-94/95
la. Draw the V and M Diagram 10kN/m 12KN/m 5kN/m 3kN-m 3m 2m 2m 3m 1b. Compute for the maximum bending stress of the given beam if the cross sectional area is: 30mm 30mm 60mm 1.c. Compute the flexural stress at 3m from the hinge if the cross sectional area is: Equilateral Triangle 100mm