s peed TC the meter-in circuit shown in the figure? The load weighs 2,908 Ibs and the cylinder piston area is 3.7

Q: 50. The movement of the cutter of the shaping machine over the work is called Select one: a.COURSE…

A: Course is a term associated with feed. Crank is a rotating link of the shaper mechanism.  Travel is…

Q: 23.A machine has a selling price of P500,000 after given 15% discount. Find the original amount.

A:

Q: Compute:  a.) The maximum shear stress developed in a 6 inch diameter solid steel shaft that…

A:

Q: Can you help me with this problem?

A: The image shows a part drawing for a wire electric discharge machine (EDM). The objective is to…

Q: Use finite differences with Ar = Ay = 1 to determine the temperature at the remaining points on the…

A: The given problem involves the application of FDM. So the heat conduction equation in 2-D should be…

Q: B. A Highway Engineer tabulates the following ADT for the Highway that will be constructed. the…

A: AADT* k factor = hourly volume design The k factor is the hourly volume adjustment factor for the…

Q: Use one main program and then a subprogram to machine the pockets. Write the subprogram in absolute…

A: We must create both the main program code and the subprogram code in order to address the…

Q: Completely solve and box the final answer. Write legibly 4. Compute the required size of the motor…

A:

Q: 2. A turbine operates under steady flow conditions, receiving steam at 1200 kPa, enthalpy 2785…

A: Given Data h1=2785 kJ/kg C1=33 m/s Z1=3 m h2=2512 kJ/kg C2=100 m/s Z2=0 m Q=-1.8 kJ/s

Q: two pulleys are connected by a belt. The nubers of RPM of the two pulleys vary inversely as their…

A: Given data: The diameter of pulley 1 is, d1 = 25 cm. The diameter of pulley 2 is, d2 = 40 cm. The…

Q: A horizontal wind turbine  gearbox is needed to provide 30:1 increase the speed, while minimizing…

A:

Q: ven questions are subparts.. Kindly solve all a, b, c and d all answers otherwise leave it. Thank…

A: A) length of link AB=6002+3002                               =670.0 mmvelocity of point B=VB→ or…

Q: . VELOCITY ANALYSIS. For the single-degree-of-freedom mechanism shown below, the angular velocity on…

A:

Q: Construct a Main Schedule of the machine tool of your choice?

A: The machine tool should have preventive maintenance . it is an essential thing for the properly and…

Q: The piston displacement of an air compressor is 1200 liters per minute. Its bore and stroke are 12…

A:

Q: A pressure of 550 kPa and a velocity of 20 m/s. the inlet port is 40 meters above The floor level.…

A:

Q: A flat belt of thickness 11 mm is used to transfer power between from electric drive motor running…

A:

Q: Find Ixx for the given Plane, where b1 =160m, d1=25m, b2=20m, d2=90m, b3=60m & d3=25 m (Enter only…

A: Given data:-b1=160m, d1=25m, b2=20m, d2=90m, b3=60m, d3=25mArea of section 1, A1=160×25=4000m2Area…

Q: In a turning operation on carbon steel with hardness- 175 HB. the cutting speed - 225 m/min, feed-…

A: GivenV=225m/minf=0.25mm/revd=7.5mmη=90% Cutting energy for Brinell hardess 175Hb=1.6J/mm3U=1.6J/mm3

Q: Need full accurate RRL .  For both 1. height of sweet potato plants. 2. programable  speed of a…

A: The question is asking for a detailed review of related literature (RRL) on two distinct topics: the…

Q: Note: The question is solved, but I want a comprehensive explanation of how to use the energy method…

A: Approach to solving the question: Using the energy method. Detailed explanation: Examples: Key…

Q: The wind velocity on the upstream side of a wind turbine is 5.2 m/s. If the turbine extracts 31% of…

A:

Q: A container is floating in water. The container has a rectangular shape of 1.52 X 0.66 X0.50 m (LXW…

A:

Q: In a milling machine the distance the workpiece advances under the cutter is known as Select one: a…

A: Option d is correct.

Q: A sky lantern which a child tied to a piece of stone on the ground at the side of a tall multi-…

A: Given:v1=2.7 m/st=2.5 sec

Q: A scene-of-the-crime-operative is called to investigate a dead body that has just been found. She…

A: Given data, 1st boundary condition At the time of death the body temperature is 37 °C, that means at…

Q: 1. In the given figure, gear 1 has 24 teeth and gear 2 has 70 teeth of PD=4. Gear 3 has 20 teeth and…

A:

Q: A flow shop consists of 3-Machines on which 4-Jobs have to be scheduled in a fixed sequence. The…

A: Given:To find:

Q: What will be the velocity of the follower at 90° using the following equation with segment angle…

A: Find the velocity of follower .

Q: b) Calculate the inclined angle λ and orthogonal rake angle yo, when yx =10°, yy =8°, ps=15°.

A:

Q: A.) A cutting operation is performed on a piece of metal. The rake angle of the tool, α, is eight…

A:

Q: Completely solve and box the final answers. Write legibly 5. How much twisting moment in lbf-ft is…

A:

Q: A piston engine in which the bore and stroke are of equal dimension is referred to as a "square…

A: Given:Let bore be 'D' and stroke be 'L'For a square engine, D = LNo of cylinders, n = 8Displacement…

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.