s) A cylinder that is 750 mm in diameter and 2.5 m long has a specific weight of 835 N/m³. It eid down into position with a cable attached to the sea floor. At this location, the sea is 500 m deep and the cylinder is to be held in a fully submerged position just 3 m above the sea floor. Find the resulting tension in the cable.

s) A cylinder that is 750 mm in diameter and 2.5 m long has a specific weight of 835 N/m³. It eid down into position with a cable attached to the sea floor. At this location, the sea is 500 m deep and the cylinder is to be held in a fully submerged position just 3 m above the sea floor. Find the resulting tension in the cable.

Name: s) A cylinder that is 750 mm in diameter and 2.5 m long has a specifi
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: s) A cylinder that is 750 mm in diameter and 2.5 m long has a specific weight of 835 N/m³. Iteid down into position with a cable attached to the sea floor. At this location, the sea is 500 m deepand the cylinder is to be held in a fully submerged po

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The total pressure force of a square plate is 25 kN, placed vertically in water so that the center of the plate is 1.5 m below the free surface. Determine the size of the plate and the depth of center of pressure. The above square plate is taken out of the water which weighs 370.5 N in air and 180.3 N in water of specific gravity 0.99. Find the volume and specific gravity of the square plate. Draw a neat sketch.
the system in the figure is in equilibrium. Calculate the gauge pressure (Pg= … kPa) measured on the manometer at the bottom and the height of the mercury in the column (ZHg= …m)? You choose the density and gravity value of mercury, water. The value of the mass on the piston will be M=229kg.
A car of mass 250 kg and volume of 64 m3 is submerged in s river. A crane is used to pull the car from river with the help of a rope. Calculate the tension in th rope.
Find the surface tension of the water droplet of 30 mm diameter when the inside pressure is 3.5 N/m2 The surface tension in N/m is
Calculate the hydrostatic force and components of the semicylindrical protuberance located at the bottom of the tank. It has a length of 9 feet inward.Do it as a new job.
The system in the figure is in equilibrium. Calculate the gauge pressure (Pg= … kPa) measured on the manometer at the bottom and the height of the mercury in the column (ZHg= …m)? You choose the density and gravity value of mercury, water. The value of the mass on the piston will be M=229kg.
The flat square of side length 2 m is submerged vertically in water, 2 m below the surface as shown. Find the fluid force against the surface. Use density of water is 9810 n/m^3.
Consider the pressure and force acting on the pool retaining a reservoir of water. Suppose the pool is 50m wide and the water is 8m deep, as illustrated below. (a) What is the Gauge pressure on the dam due to the water? (b) What is the absolute pressure at10m depth of the dam? (C) Calculate the force exerted against the dam. Density of water is 1000kg/m3.
A tank contains water up to a height of 10 m. One of the sides of the tank is inclined. The angle between free surface of water and inclined side is 60 degrees. The width of the tank is 5 m. Find the force in kN exerted by the water on the incline side. ( With Free Body Diagram)