s-156. Determine the length b of the triangular load and its position a on the beam such that the equivalent resultant orce is zero and the resultant couple moment is 8 kN m clockwise.

Q: (3) The beam is subjected to an internal moment of M = 50 kN.m as shown. Determine the percentage of…

A: parallel axis theorem : The parallel axis theorem, also known as the Huygens–Steiner theorem or…

Q: For the given shear diagram shown: V (kN) 10 - 2nd-degree curve в с D E A x (m) -2 -8 3 2.

A: Shear force and bending moment diagram represent the forces acting and moments acting on the…

Q: 2-2-2 Two identical 1.5in diameter solid struts are used to support the load at A. Find P if the…

A: Given : Dia of solid struts = 1.5 in. Vertical displacement of point A is 0.025 in. and E  29000ksi…

Q: For the overhanging beam, determine (a) load; and (b) the maximum value of Ely E Function. 24 kN

A:

Q: The beam is supported by a pin at A and a roller at B which has negligible weight and a radius of 15…

A: Consider the free body diagram of roller at C shown below. Here, FB is the frictional force at…

Q: Force F acts on the frame such that its component acting along member AB is 650 lb, directed from B…

A:

Q: The overhang of the beam carries a 6 k-ft moment. If El is constant. Determine the following 6 k-ft…

A:

Q: 12-6. Determine the elastic curve for the cantilevered beam, which is subjected to the couple moment…

A: FInd reactions at 'A'∑ M=0MA=M0∑ Fy=0 -RA+0=0 RA=0 Moment equation: Mx=Mo

Q: *8-24. Determine the slope at B and the maximum displacement of the beam. Use the moment-area…

A:

Q: 10 EN/m 2 Nim 2kN

A:

Q: 4 kN/m LA E |C D. 2 m 3m 2 m 10 kN 1 m 15 kN

A:

Q: Q.7.7 The fixed beam ABhas a hinge Cat mid span. A concentrated load Pis applied at C. Wnat is the…

A:

Q: The 30m long compound beam has an internal hinge at point E and is supported by pin C roller D and…

A: Sketch the free body diagram of the beam:

Q: 2-25. If F = 30 Ib and F, = 40 Ib, determine the a and o so that the resultant force is directed ala…

A:

Q: Problem: Determine the nominal or theoretical moment capacity of the beam = 60000 psi and f'¸ = 4000…

A:

Q: Р9-2 12 mm The beam is subjected to a shear C125 mm force of V = 25 kN. Determine the shear flow at…

A: Introduction- The beam is a structural component that typically resists loads applied to the beam's…

Q: What is the Maximum moment in kN-m. Given: w- 42, a - 5, b- 3, and c- 2. w kN/m tomt bm am Ro RA

A:

Q: total force of the water on the curved section AB.

A: Additional storage above the spillway crest can be made available by the installation of temporary…

Q: The uniform continuous beam with two equal spans I = 10m is loaded by two forces P = 10KN and P2 =…

A:

Q: Determine the resultant of the force System shown in Fig: and locate it with respect to point B 20…

A: Draw FBD: Calculating the resultant force: ∑Fy=0 ↓-FResultant=-20+200-100-6FResultant=74 Unit

Q: What is the maximum absolute shear for the following beam and load group? Use L = 19, a = 4, b = 3,…

A: you can clearly understand if you follow the below solution

Q: Two equal steel beams are built-in at one end and connected by a steel rod as shown. Show that the…

A:

Q: Calculate the Shear Force at point A of the following Beam. Take X=35 kN and Y=80KN YKN X kN/m A, D…

A: Given, Beam,

Q: , The compound beam is fixed at A, pin connected at B, and supported by a roller at C. Draw the…

A: Free body diagram -  Fixed end moment at the point A -  MA = 600×2⇒MA = 1200 KN-m As the point B is…

Q: 3 -1 m- 'С -3m-

A:

Q: *11-36. The compound beam is fixed at A, pin connected at B, and supported by a roller at C. Draw…

A: - Let Va and Vc be the vertical reactions at joint A and C respectively, Ha be horizontal reaction…

Q: 4. The compound beam is supported by a roller at point A, fixed at point C, and the two sections are…

A:

Q: lok A 2' 6' 3' C.

A: My dear,  In this type of question we ll use load tranfer mechanism.  By shifting load we ll be…

Q: Determine the design angle ø (0° < ps 90°) between struts AB and AC so that the vertical force F has…

A:

Q: -4 ft- -4 ft |C В 6 ft Determine the shear force at point b using method of section if w = 47.1lb/ft…

A:

Q: Determine the resultant internal loadings in the beam at cross sections through points D and E.…

A:

Q: A B D E b.

A:

Q: The 100lb force Q is applied perpendicular to the section DE of the be the moment of Q about point D…

A:

Q: The 30 ft long simply supported beam slopes at a 9:12 pitch and is supported by Pin C and Roller D.…

A: The forces acting in the upward direction is positive and downward direction as negative.The forces…

Q: I0 KN DKN 6 KN m 2 2 RI Rz

A:

Q: Determine the magnitude of the pin force at C given  θ = 18° and P = 57 lbs.

A:

Q: If the resultant of the loads shown passes through point B, determine the equivalent force-couple…

A: Given figure shows a force system. It is required to determine the forces RX and RY in new system…

Q: ocated 10 meters from point A and point B is located midway between A and C. The beam is supported…

A: Hello dear this is the solution of your problem Please see the attached solution, thanks

Q: For the overhanging beam with shown loading, sketch the shear and moment diagrams. 35 kN 35 kN 20…

A:

Q: Determine the magnitude of F so that the resultant couple acting on the beam is 1.7 kN-m clockwise.…

A:

Q: Determine the internal force and shear force, and the bending moment in the beam at Points C and D.…

A: Given  The beam is shown in which at joint A there is a pin joint, so the components are horizontal…

Q: Determine the maximum positive moment at C using influence line and considering the given loads…

A:

Q: ompute moment (kN-m) at support D. 200 KN 24 kN/m Sm

A: It is statically indeterminate structure It is solved by moment distribution method or slope…

Q: For the beam shown, find for the moment area the strain at D and the rotation at A, using the…

A:

Q: Determine thee maximum positive shear and moment in the beam given that F=18 kN, U= 6kN/m and L=9 m

A:

Q: 4-142. Replace the distributed loading by an equivalent resultant force, and specify its location on…

A: A beam is given with a uniformly distributed load (udl) and a uniformly varying load (uvl) as shown…

Q: Determine the shear value (kN) when x = 1.4m from the left side of the beam where: L = 4.2 m; Wo =…

A:

Q: Determine the internal shear and moment in the beam as a function of x throughout the beam. x is…

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.