Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A concentrated load of P = 22 kips is applied to the free end of bronze rod (3). Determine the magnitude of the deflection of rod end D after the temperature of all rods has increased by 70°F. Use the following dimensions and properties: a = 3.5 ft, b = 7.3 ft. Rod (1): d₁1.10 in., L₁ = 13ft, E₁ = 15,200 ksi, a₁ = 12.20 x 10-6/F. Rod (2): d₂ = 0.70 in., L₂ = 9ft, E₂ = 28,000 ksi, %₂ = 9.60 x 10-6/°F. Rod (3): d = 1.15 in., L = 6ft, E3 = 15,200 ksi, a3 = 12.20 x 10-6/°F. VD = i L in. (1) a L3 B (3) OD P b Rigid bar (2) L₂

Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A concentrated load of P = 22 kips is applied to the free end of bronze rod (3). Determine the magnitude of the deflection of rod end D after the temperature of all rods has increased by 70°F. Use the following dimensions and properties: a = 3.5 ft, b = 7.3 ft. Rod (1): d₁1.10 in., L₁ = 13ft, E₁ = 15,200 ksi, a₁ = 12.20 x 10-6/F. Rod (2): d₂ = 0.70 in., L₂ = 9ft, E₂ = 28,000 ksi, %₂ = 9.60 x 10-6/°F. Rod (3): d = 1.15 in., L = 6ft, E3 = 15,200 ksi, a3 = 12.20 x 10-6/°F. VD = i L in. (1) a L3 B (3) OD P b Rigid bar (2) L₂

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A concentrated load of P = 24 kips is applied to the free end of bronze rod (3). Determine the magnitude of the deflection of rod end D after the temperature of all rods has increased by 115 Fo. Use the following dimensions and properties: a = 3.5 ft, b = 7.5 ft. Rod (1): d 1= 1.10 in.,L 1= 12 ft , E 1= 15,200 ksi , a 1= 12.20 × 10 - 6 /Fo. Rod (2): d 2 = 0.65 in. , L 2 = 10 ft , E 2 = 28,000 ksi, a 2 = 9.60 x 10 - 6/Fo. Rod (3): d 3 = 1.15 in. , L 3 = 6 ft, E3 = 15,200 ksi , a 3 = 12.20 x 10 - 6/Fo. (1) L (2) b L2 a Rigid bar A (3) L3 vD = i in.
A 3mm thick hollow polystyrene cylinder (E = 3 GPa) and a rigid circular plate (only part of which is shown in Figure 2) are used to support a 6mm diameter steel rod AB (E = 200 GPa) of length 250mm against a rigid baseplate. If a 3.2 kN load P is applied at B, determine the following: - (a) the elongation of rod AB. (b) the deflection at point B. (c) the average normal stress in rod AB. 30 mm 250 mm A 6 mm P= 3.2 kN 50 mm Circular plate Polystyrene cylinder Baseplate
EXAMPLE 4.2 The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm²; link CD is made of steel (E = 200 GPa) and has a cross-sectional area of 600 mm?. For the 30-kN force shown, determine the deflection (a) of B, (b) of D, (c) of E. %3D 0.4 m 0.3 m 30 kN D E -0.4 m 0.2 m
The system shown in the figure has a fixed support at A and an alumimum rod of 0.5m length at C. The beam AC is subjected to a point load of 20 kN at its midspan. In addition to that point load, alumimum rod is subjected to a temperature decrease of 25 °C. Determine the deflection and the rotation at point C. Anhunnd 70 GP in
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 512 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 643 mm2. For the 32 kN force shown, determine the deflection of D (mm) *Note: Negative if compression and positive if tension. Also, the final answer should have two decimal places.
Prob 5. Calculate the maximum deflection dmax and the angle of deflection on the supports of a uniformly loaded simple beam loaded as shown. The maximum bending stress is o=60 MPa. The cross section of the beam is square with a length of 8 cm on each side. The beam is made of aluminum having modulus of elasticity E = 70 GPa. q = 2.0 kN/m L= 2.0 m
Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. 0.4 m 0.5 m B P 20-mm diameter 60-mm diameter 2. What is the value of Q in kN so that the deflection at A is zero if P = 59 kN?
A loaded beam is shown in figure. EI B Rigid L 2 M M AB is flexible and 'BC' is rigid. Maximum deflection is
The beam shown below is suspended from two steel rods as shown and is initially horizontal. The midpoint B of the beam is deflected 15 mm downward by force Q. The steel used for the rods has properties E = 200 GPa and σ = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
The beam shown below is suspended from two steelrods as shown and is initially horizontal. The midpointB of the beam is deflected 15 mm downward byforce Q. The steel used for the rods has properties E= 200 GPa and  = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is applied to the end B of the shaft. Determine the rotation of section B. The shaft and beam are made of an aluminium alloy for which E= 720 GPa and G = 27 GPa, Neglect the strain energy of the hub DF. IC 400 mm 200 mm- 40.0 mm D 60.0 mm 400 mm 800 mm HO H 30.0 mm T= 2.00 kN.m
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm; link CD is-made of steet E = 200 GPa) and has a cross-sectional area 600 mm. For the 30-kN force shown, determine the deflection (a) of B, (b) of D, (c) of E. 0.4 m 0.3 m 30 kN E T0.4 m 0.2 m