restrained by rigid supports at A and E at room temperature of 20°C. For the system shown determine when the environmental temperature will reach to 140°C (a) the reactions at A and E, (b) the deflection at point C Bronze E-105GPA a-21.6x10 C Stainless steel E-200GPA a=17.3x10 C Dimensions in min 100 -120-- 100 180- DI Bress 60 kN 40 kN

Q: Learning Goal: To determine the in-plane principal stresses and maximum shear stress along with…

A: Step 1: Step 2: Step 3: Step 4:

Q: Aim: To conduct a full kinematic analysis and calculate dynamic reaction forces in a linkage…

A:

Q: A 4.8 m long from fixed point, 0.5 m wide and assumed a thickness of 30 mm throughout a springboard…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: A gauge # 10 HSLA steel for an automotive application has a Young’s modulus of 200 GPa, a yield…

A: Find the punch force required

Q: The next three question relate to the modified Goodman diagram with the following baseline data. A…

A:

Q: Which material has the greatest UTS?

A: The ultimate tensile stress is the maximum stress in the material corresponding to the strain.

Q: The table gives data concerning the shrink fit of two cylinders of differing materials and…

A:

Q: What is the whal factor of a spring if it has the characteristics average diameter 200 mm, wire…

A:

Q: reduction in area

A: Given: Initial diameter D=15.55 mmFinal diameter d=7.35 mm TO determine: The percentage reduction in…

Q: A cylindrical specimen of some metal alloy having an elastic modulus of 123 GPa and an original…

A: A cylindrical specimen given Load P=2170NG=123GPad= 3.5mmAllowable elongation = 0.46mm

Q: n ductile materials occurs when the stresses at the crack tip ation factors for ductile materials…

A: a) factor of safety is always used while designing a components ( True)  b) small radius of…

Q: A) An engineer works for a company that has many gray cast iron rods of different diameters and…

A: Given :Load P = 10 kip Material : grey cast iron

Q: Sketch stress strain curve if the result shown in table represent the force and extension happened…

A: a. Stress - strain curve:

Q: Problem 2 out of 2: A metal initially having a diameter of 8 mm and a gauge length of 40.0 mm is…

A:

Q: -Answer the following questions by referring the given figure: (0.5 material specification + 0.5…

A: Dear student,                    As you have already have answer of first three subparts so I am…

Q: in 20 min and thank DYBALA 8

A:

Q: Which material should be chosen when high strength is required

A: Given: To define: Which material should be chosen when high strength is required

Q: Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear…

A: Given data: Stress=σ Strain=ε Need to draw the graph between the stress and strain.

Q: 4. A 25 mm diameter steel rotating shaft in a machine is loaded as follows: $ = 25mm Rotating M T…

A:

Q: If 80% of samples has a compressive strength greate than x, calculate the value of x (to 1 decimal…

A:

Q: о ре cional area

A:

Q: The state of stress at a point in a structure is depicted in Fig. 1. Calculate the normal stress and…

A: Given Data:   To Find: (a) The normal stress σ. (b) The angle θ.

Q: 2. A rectangular steel bar 0.5 inch thickness by 1.5 inches width and 220 ft long is subjected to a…

A: Given: Thickness of the steel bar is 0.5 in. Width of the steel bar is 1.5 in. Length of the steel…

Q: Pls answer thank you! A circular rod is 128 mm in diameter and carries gauge marks placed 50.8 mm…

A:

Q: In the First project: you have been asked to perform tensile testing for four different materials…

A:

Q: In the graph, the module of toughness can be shown to be represented by: A) The area associated…

A:

Q: This subject is strength of materials show complete and clear solution with free body diagram and…

A:

Q: .. An machine part is being tested with a load of 63,000 lb. The allowable tensile stress is 10,000…

A: Given:Allowable Tensile Stress on machine=σmaximum=10000 psi(pound per square…

Q: PLS MADE A FBD DIAGRAM !!!!! easy!!!!!! there is a rubber mat circled in yellow that is non slip and…

A: It is asked to calculate the reactions in the rubber mat.

Q: Tensile test had made to cylinder shape with diameter 3.0 In and length 5.7 In. It had maximum…

A:

Q: a. generate the stress-strain curve for aluminum b. Indicate the following points in the…

A: whenever the shear force acts aluminum does not show any deformation. As the yield point is too…

Q: A tensile test was performed on a metal specimen with a diameter of 1/2 inch and a gage length (the…

A:

Q: Please answer these three questions. Thank you!   A material has a Poisson’s ratio of -0.2 . Which…

A: Givenpart 1A material has a Poisson’s ratio of -0.2 . Which of the following is true?a. Strain is…

Q: You have built the majority of the tension testing machine, but much of the instrumentation is still…

A: The diameter is

Q: An alloy steel having a diameter of 0.45 in. extends 0.002 in. over a gage length of 2.2 in. due to…

A:

Q: 41) A 19mm diameter cylindrical rod is subject to extreme loading. It must withstand a 75000 N…

A: Given:

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.