Required information The figure shows a 400-mm-diameter brake drum with four internally expanding shoes. Each of the hinge pins A and B supports a pair of shoes. The actuating mechanism is to be arranged to produce the same force Fon each shoe. The face width of the shoes is 75 mm. The material used permits a coefficient of friction of 0.22 and a maximum pressure of 1000 kPa. Consider a = 0.150 m, R= 0.20 m, d= 0.050 m, and c= 0.165 m. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 15° 15° F F a +a 10 10 10 B 10 FF 15° 15° Determine the following forces acting on the hinge pins of the brake. Rx1 (primary shoe) is kN. Ry1 (primary shoe) is kN. Rx2 (secondary shoe) is kN. Ry2 (secondary shoe)| kN.

Required information The figure shows a 400-mm-diameter brake drum with four internally expanding shoes. Each of the hinge pins A and B supports a pair of shoes. The actuating mechanism is to be arranged to produce the same force Fon each shoe. The face width of the shoes is 75 mm. The material used permits a coefficient of friction of 0.22 and a maximum pressure of 1000 kPa. Consider a = 0.150 m, R= 0.20 m, d= 0.050 m, and c= 0.165 m. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 15° 15° F F a +a 10 10 10 B 10 FF 15° 15° Determine the following forces acting on the hinge pins of the brake. Rx1 (primary shoe) is kN. Ry1 (primary shoe) is kN. Rx2 (secondary shoe) is kN. Ry2 (secondary shoe)| kN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Qs.The strength of the longitudinal joint is 25 kips/ft, whereas for the girth joint it is 20 kips/ft. Calculate the maximum diameter of the cylindrical tank if the internal pressure is 110 psi. Also discuss the joint strength and diameter of tank requirement for the given conditions .If you dont know the answer please skip and let others do , dont post wrong answer, dont waste qsn
The acrylic plastic rod is 300 mm long and 15 mm in diameter. If an axial load of 200 N is applied to it, determine the change in its length and the change in its diameter. Ep = 2.70 GPa, v, = 0.4. (Fallow Elong, Ela) 200 N 300 mm 200 N
Question 2 A rectangular plane surface is 3 m wide and 6 m deep. It lies in vertical plane in water. Calculate and determine the total resultant force (kN) the position of the center of pressure (COP) on the plane surface when its upper edge is horizontal and 3.5 m below the free water surface. Represent your result on a sketch. [lc xsin? e BH Hint: show all the steps. hp = hc + Ic 12 g= 9.81KN/m hcxA
TWO CONCRETE BLOCKS WEIGHING 1800 N EACH FORM PART OF THE RETAINING WALL OF A SWIMMING POOL. WILL THE BLOCKS BE IN EQUILIBRIUM WHEN THE POOL IS FILLED, AND THE POOL EXERTS THE LINE LOADING SHOWN? IF YES, WILL IT SLIDE OR TIP? ALSO, DETERMINE THE HEIGHT OF WATER IN WHICH THE POOL WILL BE FILLED SUCH THAT THE BLOCKS WILL BE IN EQILIBRIUM. 300 mm 540 mm A-0.5 540 Plastic liner mm A-10 6Nmm
Considering the effects of the prestressing forces (assume no loss) and the working loads (include the selfweight of the beam). Calculate the stress indicated below. Calculate fbot at midspan. (MPa), consider sign convention (- for compression, + for tension) 5 KN/m EXCLUD In6 SELFWEIGHT 300 = P P=300 kN ISM オ 400 de =24 IN m3 N.A. 800 70 T
The press plungers of a Bramah (hydraulic) press is 40cm² in cross-section and is used to lift a load of mass 800kg. What minimum force is required to be applied to the pump plunger if its cross-sectional area is 0.02m²? E
Considering the effects of the prestressing forces (assume no loss) and the working loads (include the selfweight of the beam). Calculate the stress indicated below. Calculate ftop at the ends. (MPa), consider sign convention (- for compression, + for tension) Skw/m EXCLUD in6 SELFWEI6HT 300 =P P=300 kN ISM オ 400 片 de = 24 IN m3 N.A. 800 70
Q.4 Springs A close-cooled helical spring is to carry a load of 150 N. The mean coil diameter has to 10 times that of the wire diameter. If the maximum shear stress is not to exceed 100 N/mm2, calculate the diameter of the coil.
130 N A 30 mm C Determine also: a) Force at A b) Force at B c) Force at C В D -40 mm- -60 mm Analytical solution, two digits behind comma.
Problem-5 A compression spring is made of a music wire of 2 mm diameter having a shear strength and shear modulus of 800 MPa and 80 GPa respectively. The mean coil diameter is 20 mm, the free length is 40 mm and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately...
Q1. Find: (a) the stress in the Steel and Aluminium rods after the loap P applied and the temprature raised 60 C° and (b) the displacement under the load P. Using the data in the Table below. (30 Mark) Rod A (mm') a (µm/m. Cº) L (m) d (m) 0 (degree) E (GPa) P (kN) Steel 400 11.2 190 44 Aluminium 350 18.9 35 85 Aluminium A Steel 4m d + 2m P
The strength of the longitudinal joint is 25 kips/ft, whereas for the girth joint it is 20 kips/ft. Calculate the maximum diameter of the cylindrical tank if the internal pressure is 110 psi. Also discuss the joint strength and diameter of tank requirement for the given conditions.