!Required informationConsider the beam and loading shown.Given: X = 25 kipsX을 in.|n7.25 in.AB$1.5 in.1,5 in.20 in.-을 in.20 in.-in.-10 in.8 in.-Determine the shearing stress at point a. (Round the final answer to three decimal places.)The shearing stress at point a is|ksi

As the loading is symmetric so,RA = RB = 25 Kips

Required information Consider the beam and loading shown. Given: X = 25 kips X X in. 7.25 in. B 1.5 in. 1.5 in. in. in. 20 in.- 20 in.- 10 in. 8 in.- Determine the shearing stress at point a. (Round the final answer to three decimal places.) The shearing stress at point a is |ksi

Required information Consider the beam and loading shown. Given: X = 25 kips X X in. 7.25 in. B 1.5 in. 1.5 in. in. in. 20 in.- 20 in.- 10 in. 8 in.- Determine the shearing stress at point a. (Round the final answer to three decimal places.) The shearing stress at point a is |ksi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

University of Warith Alanbaya Civil Engineering Department Mr. Safa'a Sabry M. Engineering Mechanies Chapter Two - 1 Homework 1 Q.4. Determine the magnitude of the resultant force FeF+F and its direction, measured counterclockwise from the positive x-axis. Q.1. Determine the magnitude of the resultant force acting on the screw eye and its direction measured clockwise from the x-axis. F 250 lb 09 30 2 kN 6 kN Q.2. Two forces act on the hook. Determine X- the magnitude of the resultant force. 45° F2= 375 lb Q.5. If0 = 60° and F=450 N, determine the magnitude of the resultant force and its N 00 direction, measured counterclockwise from the positive x-axis. Q.6. If the magnitude of the resultant force is to be 500 N, directed along the N 00, Q.3. Determine the magnitude of the resultant force and its direction positive magnitude of force F and its direction y-axis, determine the measured counterclockwise from the positive x-axis. N 008 IS X- N 00 N N 009
The beam supports the triangular distributed load shown below with Wmax=770 lb/ft. The reactions at A and B are vertical. 6 ft BI D 6 ft C 6 ft W B E 4.5 ft 4.5 ft
Required information Consider the beam and loading shown. Given: P= 8 kips 글 in. P 8 in. a 4 in. - in. - 4 in. 16 in. 12 in. 16 in. Determine the largest shearing stress in section n-n. (Round the final answer to two decimal places.) The largest shearing stress is ksi.
" and the calculation 17 73 pror W₁ B P 2m 2m Use the following tables as template for your solution. hear Relation of Shear to Concentrated and Distributed Load VB - VA = Bending Moment Calculation Relation of Bending Moment to Applied Moment and Shear Diagram MB - MA = VI CO W₂ M Bo 5m Shear Values (N) VA = VB = Shear Values (N) MA = MB =
es A 4-m cantilever beam is loaded as shown. The cross section is formed with two concentric circles of radii 45 mm and 35 mm. If the allowable stress is 150 MPa, F Ra 1 X Y 12 Determine the section modulus of the beam. Select the correct response: 72113.831 mm³ 87833.695 mm³ 57962.384 mm3 45378.561 mm³ Ri 12
A mechanic uses a crowfoot wrench to loosen a bolt at E. Knowing that the mechanic applies a vertical 20-lb force at A, determine the principal stresses and the maximum shearing stress magnitude at point Hlocated as shown on top of the 4 -in. diameter shaft. (Round the final answers to two decimal places.) H E 6 in. B 10 in. The maximum principal stress is Omax |ksi and the minimum principal stress is Omin |ksi (+ tensile; - compressive). The maximum shearing stress magnitude is ksi.
イ H.W.pdf -> A simplified model as shown in figure below of a planur robotie urm. You may ussue thut each segment has length 1.5 m, aad the applied force is 250 N. 0, = 35 and -0,- 20. Calculate dhe aoncnt that the force, F. cacits about dhe point A ...
☑ How Find max. tensile and comporsive stresses. P 5KN.M 15AN Im 2m 2m B A IN.A= 60×10 mm" 60 12
Find the diameter of dAB dec bar if the stress equal to 0.15GPA C 120cm B 125kN 125KN 90cm A 60kN
Required information Consider the loading condition shown. Assume that the flexural rigidity El of the beam is constant. 21 W B -L/2L/2L/2- The deflection at point B is. 0013 W Using singularity functions, determine the deflection at point B and point D. (Round the final answers to four decimal places.) The deflection at point Dis. -0.0163 wwwwwwwwww………… 1 D x Deflection point at D is wrong
Problem 4 The beam loaded as shown below, compute the bending stresses at every 1m from the fixed end support of the beam use Ina = 100x106 mm4 www 10 kN 4 kN/m bm 러 n.a. 130 mm 200mm
I RevieW The 1.16-in.-diameter rod in (Figure 1) is subjected to the loads shown. Part A Determine the state of stress at point B. Express your answers, separated by commas, to three significant figures. IVα ΑΣφ. vec ? OB =, (Tzy)B =, (T2)B = ksi (C), ksi, ksi Figure 1 of 1 > Submit Request Answer < Return to Assignment Provide Feedback 9 in. 200 lb 300 lb 1200 lb in.