Replace the three forces acting on the shaft by a single resultant force. Specify where the force acts, measured from end A.

Q: Q6/ Water at 15°C is to be heated to 65°C by passing it over a bundle of 4-m-long 1-cm-diameter…

A:

Q: Mechanical Engineering Two steel beams are used to span a creek to serve as a bridge. The creek is…

A:

Q: A pump delivers 95 liters per second of water through a 203 mm diameter suction pipe and 152 mm…

A: Given:Q=95 L/s =95*10-3 m3/sds=203 mmdd=152 mmLs=3 mLd=21 mh=20 mhls=0.10 mhld=0.20 mf=0.025η=0.75

Q: ar the given beam find maximum slope and maximum deflectior t B. Take E= 200KN/mm2 and /= 100 x 10 m…

A:

Q: a) Find COP of the R12 Refrigeration System b) Draw the h-p diagram and explain each step

A: Condenser temperature, Tc=40oCEvaporator 1 temperature, T1=-10oCEvaporator 2 temperature,…

Q: urbine has an available enthalpy of 3300 kJ/kg in a Rankine cycle. The pump work has also 25 kJ/kg.…

A: Given:WT=3300 KJ/KgWp=25 KJ/Kgm=3 Kg/s

Q: Read the questions carefully and answer with complete solution and units. Use the steam tables…

A:

Q: What is the position function x() for the object? Take x=0 to be the position of the object when the…

A:

Q: ug the above info into Newton's law of cooling: (T=A+Be^kx) Write your answer as a time, not just…

A:

Q: GIVEN A thin rectangular plate having a width w and a heigh h is located so that it is normal to a…

A:

Q: 9. The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a…

A:

Q: 1. Calculate the moment of inertia with respect to the X-X centroidal axis for the areas shown. 40…

A:

Q: The motion of particle is defined by the relation a=4t, where a is in m/s2 and t in seconds. It is…

A:

Q: Derive the formula for the nonflow work in terms of P1, V1 and V2 only for a constant temperature…

A:

Q: A piston/cylinder arrangement contains 2 kg of ammonia at a temperature 132.45 ℃ and a pressure 5…

A: A thermodynamic cycle (state I → state f ) is supposed to be reversible in the event that the…

Q: -The connection shown in the figure if the screw is type 98 and the two plates are A'SI 1040 CD…

A:

Q: kinelic enorgy ol tro hoop it gium y: the hoop. Then, Cakulale the 1oling down without slipping an…

A: As per the guidelines we are subjected to solve only one question at a time please repost the same…

Q: The circular punch B exerts a force of P = 1.7 kN on the top of the plate A. (Figure 1) Figure <) 1…

A:

Q: In a combustion engine with a diameter of 6.08in, and distance of 2.462in with ratio of 8.3:1 and a…

A: The work done in a constant pressure process can be calculated using the formula given below-…

Q: The 41-lbrectangular access door is held in the 90° open position by the single prop CD. Determine…

A:

Q: Determine the difference between the total pressure of an aircraft flying at sea level, and an…

A: Given, Velocity of both the aircrafts = v = 100 m/s Altitude of the first aircraft = h1 = 0 km (At…

Q: the Theorem of Pappus to determine: a) the volume of the figure, and b) the surface area of the…

A: Given:

Q: 2. Explain how to compile and run a program with the help of a diagram

A: Given Data : Program Compile and Run

Q: Differentiate the operation, structure and usage of (1) reciprocating air compressors and (2) rotary…

A: A type of compressor that uses a rotary -type of positive displacement mechanism is a Rotary-Screw…

Q: Block A has a mass of 4 kg and block 8 of 4 kg Neglecting the mass of the pulleys, find the tension…

A:

Q: A shaft fitted with a flywheel rotates at 350 r.p.m. and drives a machine. The torque of the machine…

A:

Q: Determine the largest weight W that can be supported by two wires shown in the figure below. The…

A:

Q: Assign ment 8 Calculate Runetions of de flection, slope, shear Porce and beding monent of the beam,…

A:

Q: The discharge of water through a horizontal pipe is 0-25 m'/s. Its diameter, which is 200 mm,…

A: Given dataDischarge = 0.25 m3/sDiameter of pipe 1 = D1 = 200 mm = 0.2 mDiameter of piper 2 = D2 =…

Q: - 1-why generally the voltage is applied to H.V.side?

A: Voltage is applied to HV side.

Q: 1. A centrifugal fan is delivering 2000 cfm of air at a total pressure differential of 2 in.w. The…

A: Dear student,                    According to the guidelines I am allowed to answer only three…

Q: 6-7. Water flows through the hose with a velocity of 4 m/s. Determine the force that the water…

A:

Q: the rod diameter is 3 cm, find i) Hydraulic pressure during the extending stroke. ii) Piston…

A: Dear Student, As per guidelines I am allowed to solve first three sub Questions Only ( in case of…

Q: For the frame shown, the wood has a normal failure stress of 42 MPa, and a shear failure stress of…

A: Given DataNormal failure stressσf=42MPashear failure stressσfs=10MpaLoadP=40kNFactor of safetyFOS=2

Q: Below is the schematic design of cable bridges. If the force acting on the cable T1 = 100kN,…

A:

Q: (Torque applied)

A:

Q: 70° 70° F2 F1 5m 2m A column of 5m height is subject to 2 forces, F1 = 83N and F2 = 50N as shown…

A:

Q: One of the smooth verticai walls supporting end B of the 235-kg uniform shaft is turned through a…

A:

Q: A shaft fitted with a flywheel rotates at 350 r.p.m. and drives a machine. The torque of the machine…

A:

Q: The critical Reynolds number for external flow (which started as a laminar flow) over thin flat…

A: For cross flow over a long cylinder, diameter is the appropriate length parameter to be used in…

Q: Please explain how this was solved. I'm confused as to how the equation has been transposed to get…

A:

Q: H.W 1. Consider a two degree of freedom bar elements as shown in figure. Using finite element method…

A:

Q: uniform stream overflows in a circular cylinder and then a periodic Kármán vortex street is created.…

A: Use Buckingham pi method to solve this problem

Q: Define the cylinder force when the K = 550 kg and the weight of the boom is 25 kg. position of…

A: The force in the cylinder is 25234.224 N.

Q: O Find the Positive value of * Mhat stisfie the equ4ation fuse Bisection methed} x- 2X-1= o

A:

Q: A hoop (ring) is rolling down without slipping an inclined plane, whose angle is 0 at the base. The…

A: Answer: The correct answer is option (b).

Q: Problem (7,2): The surface of an airplane wing is subjected to plane stress with normal stresses oy,…

A: Given, Stress in x direction = σx = 100 MPa   Normal stress at any angle θ can be given by, σn = σx…

Q: The 1021-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 472…

A:

Q: 70° 70° F2 F1 5m A 2m A column of 5m height is subject to 2 forces, F1 = 83N and F2 = 50N as %3D %3D…

A:

Q: Calculate Runetions of de flection , slope, shear lorce and berding moment a nd draw their diagrams.…

A:

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.