Repeat question but with the load at joint 1 acting horizontally? che supports245⁰145°90°3100KN

Find: (i) The magnitude of the force in each of the three members. (ii) The magnitude and direction…

Answered: Repeat question but with the load at…

Engineering

Mechanical Engineering

Repeat question but with the load at joint 1 acting horizontally?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bracket shown in the figure is bolted a ceiling beam to support a fluctuating vertical load imposed on it. The bolts are -in coarse-thread SAE grade 8, tightened to recommended preload for nonpermanent assembly. The stiffnesses have already been computed and are kp=4 Mlb/in and km = 16 Mlb/in. Laad line F. Steady stress (a) Assuming that the bolts, rather than the welds, govern the strength of this design, determine the safe repeated load that can be imposed on this assembly using the Goodman criterion with the load line in the Figure and a fatigue design factor of 2. (b) Compute the static load factors based on the load found in part (a). (ie. Yielding factor of safety, Load factor of safety and factor against joint separation)
solve all three part by method of section
ASAP
Part A Determine the y component of support the reaction at A using scalar notation for the truss (a) shown in (Figure 1) Suppo that F 400 N Express your answer to three significant figures and include the appropriate units. ? A,= Value Units Figure 1 of 2 Submit Request Answer Part B Determine the z and y components of the support reaction at D using scalar notation for the truss (a) shown in (Figure Express your answers using three significant figures separated by a comma. 2m 2m It vec D. D, = (a)
PLEASE ANSWER NUMBER 1.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
Please i need answer for this question I have exam online now quickly please
Problem 17 A joint shown has the basic layout shown in the diagram below. (All dimensions on the diagram are in inches.) A single pin of diameter 0.5 inches (A = 0.2 in2) holds together the yoke and bar as shown. The material has an ultimate strength in tension of 80 ksi, and an ultimate strength in shear of 45 ksi. The load P has a value of 10000 lb. By examining the shear stress in the pin, the normal stress in the yoke, and the normal stress in the bar, find the overall factor of safety for the joint. P=10,000 lb YOKE -0.5 PIN BAR P=10,000 lb 1.5- 20 1.5 0.5 0.5
4. A solid shaft was made of alloy steel, it was welded to a flat plate by a specific size of fillet weld. If a torque is applied to the shaft, calculate the size of the weld joint. Power Torque Yield stress Shear stress Ultimate stress (Mpa) Compression stress (Mpa) Ductility (%) (kw) (Nm) 1000 (Mpa) 400 (Mpa) 160 280 30 Modulus of Bending Stress Bending Moment Factor of Safety Elasticity (GPa) (Mpa) 220 280 120 4 Modulus of Rigidity (pa) 70 Fracture stress (Mpa) 250
Figure Q1 shows a structure under a concentrated force of P. Pins A, B, E, and F are single-shear with a 21-mm diameter. The connections at D is double shear connection with a 21-mm diameter. All pins are made of Aluminum 2014-T6. Based on yield stress, minimum factor of safety is 1.5 for all parts of below structure. Determine maximum concentrated force P, that can apply on the structure. (The cross sectional area of members EA and FB are 330 mm² and 250 mm² respectively). 350 mm 600 mm 900 mm E Copper Brass C83400 F Copper Bronze C86100 Figure Q1 A B 720 mm P D
I need a quick solution within 15 minutes With put a happy emoji at the end my best wishes Hamoudi