Remove the 50 resistor in the given circuit and assume an operating frequency of 50 Hz and a load of 100 Q connected between terminals a and b. In the given circuit /x=8.0040° A. 160 Ω ell 50 Ω 809 1x b Determine the capacitance that must be connected between the terminals marked a and b to increase the PF of the source to 0.95. (Round the final answer to four decimal places.) The capacitance that must be connected between the terminals marked a and b is 66.182 µF.

Remove the 50 resistor in the given circuit and assume an operating frequency of 50 Hz and a load of 100 Q connected between terminals a and b. In the given circuit /x=8.0040° A. 160 Ω ell 50 Ω 809 1x b Determine the capacitance that must be connected between the terminals marked a and b to increase the PF of the source to 0.95. (Round the final answer to four decimal places.) The capacitance that must be connected between the terminals marked a and b is 66.182 µF.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship between the applied circuit voltage and the circuit current? The applied voltage lags the circuit current. The phase shift between the circuit voltage and current changes with time. The applied voltage is in phase with the circuit current. The applied voltage leads the circuit cur Previous Page Next Page Page 2 of 10
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
60. Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V de voltage source. 61 Datermine the volto in the girRuit F Figura 1 1?
If the voltage V, = 800 mV, then the current flowing in the load I, is: %3D -j20n Select one: O a. None of these O b. Is 100 <-90° mA O c. Is 5.0<.-90° A O d. Is 5 <90° mA ell
Determine the DC currents (la. lc and I) and dc junction voltages (Var Ver and Vca) la-Blank 1 mA, le-Blank 2 mA, I-Blank 3 mA, Var Blank 4 V, Vcr Blank 5 V and VcB - Blank 6 V Use 2 decimal places. Use the following values. VBB= 3V RB= 5kOhms Rc=232 ohms Vcc =18 V BDC=65
For the Photoflash unit. Vse 9V. RISKO C-1500 uf. R2= 120. The average power dissipated by the lamp is High voltage de supply 6.75W 8.3W 0.675W 10W 0.6W The mutual inductance sign for the following circuit is 352 www Negative R₂ Positive 2 mH 3 mH ell 5 mH www 10 Ω
5.) Find the percent overshoot, settling time and peak time for 0.04 T(s) == 240.002s +0.04
Very urgent. Draw the waveforms of the voltage at the load (RL) end, the voltage at the R end, the voltage at the L end and the current 1 when the switch K is turned to position 2 after a long enough time.
For the following circuit, determine the maximum power, PMa in Watts that can be transferred to the load resistor RL. Along the way you must find: (a) VTh, (b) RTh, and (c) PMaz in Watts. You must show all your work to receive full or partial credit. Put your final answers in the box provided. 15N a 102 2A( T RL 15V
An rms voltage of 22.2 V with a frequencyof 1.00 kHz is applied to a 0.290-mH inductor. (a) What is the rmscurrent in this circuit? (b) By what factor does the current changeif the frequency of the voltage is doubled? (c) Calculate the current for a frequency of 2.00 kHz
5 The voltmeters in the figure measure RMS voltages. If V, = 23 V and V, = 14.5V what is V3? %3D C R eee V2 V3 23 V None of them 8.5 V 4.5V 37.5 V O 14.5 V
Calculate the output voltage for the circuit given. The value of input voltage can be taken as 2mV, load resistor has a value of 10K Ohm and Beta has a value of 100. You MUST include the value of re' in the calculations. Please make wave-forms at each point. Vcc +20V Rc 3.3 kN C3 33 k2 out I µF RE 330 N ER2 10 ΚΩ RE2 330 2 C2 10 μF