Refrigerant 134a expands in a piston-cylinder assembly from p₁ - 160 lb/in² and T₁ = 140°F to p2 = 30 lb/in2 and T₂ = 80 °F. The mass of refrigerant is 0.44 lb. During the process, the work done by the refrigerant is 4.32 Btu. Kinetic and potential energy effects are negligible. Determine the initial volume of the refrigerant, V₁, in ft3, and the heat transfer for the process, in Btu.

Refrigerant 134a expands in a piston-cylinder assembly from p₁ - 160 lb/in² and T₁ = 140°F to p2 = 30 lb/in2 and T₂ = 80 °F. The mass of refrigerant is 0.44 lb. During the process, the work done by the refrigerant is 4.32 Btu. Kinetic and potential energy effects are negligible. Determine the initial volume of the refrigerant, V₁, in ft3, and the heat transfer for the process, in Btu.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
Solve show all steps and solution. Energy systems engineering
12
There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. Problem: A refrigeration cycle uses refrigerant R-134a to cool down water from 40°C to 20°C. The refrigerant R-134a enters the cycle as saturated liquid at -15°C and exits as saturated vapor at the same temperature. The mass flow rate of R-134a is 0.12 kg/s. The overall heat transfer coefficient is 1400 W/m².K. The surface area of the heat exchanger is 1.4 m². What is the rate at which heat is being exchanged between R-134a and water? Assume that the heat exchanger is perfectly insulated from outside (i.e., there is no convection or radiation with the outside/surrounding). Solution: We know, from the definition of overall heat…
i need the answer quickly
|Read the problem statement and the solution provided. There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. You can make the corrections directly on a copy of this provided solution, but make sure you clearly explain the corrections. Problem: Consider fully-developed flow of water through a 24-cm diameter tube. The water comes in at 20°C and exits at 40°C. The surface temperature of the tube is uniform at 60°C. The water flow has a mass flow rate of 0.24 kg/s. What is the average convection coefficient of the water flow? Solution: We have T, = 60°C, Tmi = 20°C, Tmo = 40°C, So, the bulk-mean temperature is Tm = 30°C. The appropriate properties are: u = 7.98 × 10-4 kg/ms; k = 0.615…
_% od 25m is 9m
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Please solve it complete please don't copy paste